cruise control inoperative

5 Reasons Why Your Cruise Control Stopped Working

• Updated: March 15, 2023

It would be difficult to find a vehicle on the road today without cruise control. This invaluable feature makes driving long distances easier but can also cause trouble when it malfunctions. Understanding the reasons your cruise control stopped working ensures that you can get the problem fixed quickly for a more enjoyable ride. 

While this fault can cause issues with the cruise control system itself, there could also be an effect on the acceleration of your vehicle. That’s why you want to have it looked at as soon as you notice a problem. Let’s take a quick look at the reasons your cruise control may have stopped working.

Reasons Why Your Cruise Control Stopped Working

The most common reason a cruise control stops working is due to a blown fuse or a defective brake pedal switch . It can also be caused by issues with the throttle control system or the ABS. In older cruise control systems, it can be caused by a broken vacuum line.

Here is a more detailed list of the possible reasons your cruise control is not working:

1. Blown Fuse

All electrical systems in the vehicle are controlled by fuses. Your cruise control system is attached to a fuse that can blow if there is a short circuit or fault. Without a good fuse, the cruise control system can’t work at all.

Thankfully, it’s not difficult to find and replace a blown fuse. Look in the owner’s manual to find the fuse that corresponds with the cruise control technology. 

2. Defective Brake Pedal Switch

The brake pedal switch is responsible for turning the brake lights on and off based on the pedal position. Cruise control systems are designed to disengage whenever your brake pedal gets pressed. 

Because the cruise control is wired into the brake pedal switch, any fault can cause it to stop working. When the brake pedal switch malfunctions, the car believes the brakes are engaged, causing the system to turn off automatically. Not only that, but your car’s brake light might also be stuck on, leaving confused drivers in your wake. 

3. Malfunctioning Speed Sensor

Speed sensors are located on every wheel or differential. The purpose of these sensors is to monitor the speed of the wheels to determine if traction control is needed. 

The speed sensors are also part of the cruise control system. When a sensor fails, the cruise control can stop working and the speedometer might act strange as well. 

If there is an issue with a speed sensor, it will often show with an ABS warning light or a check engine light on the dashboard.

RELATED: 3 Symptoms of a Bad ABS Wheel Speed Sensor

4. Electrical Issues

The cruise control system is electronic, with many components working together to make the system operate. If the cruise control fails to work, you want to check the wiring harness and associated connectors for a fault.

You also need to ensure that the voltage source is supplying enough power to the system. Even the smallest fault can cause defects with the cruise control. In many cases, there can be an issue with the cruise control lever or buttons causing the cruise control to not engage.

If your cruise control buttons are located on the steering wheel it could also be caused by a bad clock spring, which is located behind the steering wheel.

Check the system with an OBD2 scanner to look for any trouble codes related to the cruise control.

RELATED: 5 Symptoms of a Broken Clock Spring, Location & Replacement Cost

5. Damaged Vacuum Actuator, Hoses or Cable (Older cruise control)

If you drive an older vehicle with cruise control, you might have an issue with the vacuum actuator or the cable that connects to the throttle. If there has been damage done to the vacuum hoses or the actuator, the cruise control will stop working altogether.

Additionally, the cable linking the actuator to the throttle must be in good shape. If it has been broken, the cruise control will fail. 

What is Cruise Control?

Cruise control is a feature that is used when you are traveling at a consistent speed. Cruise control was first introduced for automobiles in the 1950s. However, it took many years before it became a staple in the modern vehicle.

This electrical system allows you to set a predetermined speed and take your foot off of the gas pedal. If you are on a long drive, there is less fatigue because you don’t have to try to maintain your speed. Cruise control can also benefit fuel economy because the vehicle uses less fuel when traveling steadily. 

In newer cars, you might be able to find adaptive cruise control , which is a smart technology. Adaptive cruise control allows you to travel at a predetermined speed, but it also helps to maintain a safe distance from the vehicles in front of you with the help of sensors. With conventional cruise control, you need to take over when the car in front of you slows down, but that’s not the case with adaptive cruise control. 

There are also vehicles nowadays with not only cruise control, but fully self-driving vehicles . We will most likely see much more of this in the future.

Cruise Control Repair Cost

The cost to repair your cruise control system depends on what caused it to fail. If you need to replace a cruise control or brake switch, you might spend between $125 and $350, including parts and labor. However, the cost to change a fuse is only a few dollars and you can perform the replacement yourself in just a matter of seconds. 

On the other hand, when something major fails, such as the actuator, you could be looking at a much higher repair bill. In some vehicles, the cost to replace a cruise control actuator can cost more than $700. These costs rise if you drive a luxury vehicle or one that is difficult to get parts for. 

It might not seem immediately important for you to fix the broken cruise control, but this defective system can affect other performance aspects. You could start to notice issues with acceleration or have trouble with the speedometer. To play it safe, it’s always best to have the cruise control repaired as soon as you notice a problem.

Is there a fuse for the cruise control?

Yes. If the cruise control is installed from the factory, you should check your car’s owner’s manual for the fuse location. If it’s an aftermarket cruise control, you’ll need to follow the wires to find the fuse.

Does the brake switch affect the cruise control system?

Yes. The brake switch affects the cruise control system. The brake switch sends a signal to the cruise control system to let it know when the brakes are being applied for the engine to know when it should stop accelerating.

Will the cruise control work if the check engine light is on?

The cruise control function will be disabled when the check engine light is on in most car models, even if the cause of the check engine light is not the cruise control itself. This is mainly due to safety reasons.

Can a vacuum leak affect cruise control?

Older vehicles use vacuum to control the throttle for the cruise control, and in this case a vacuum leak can heavily affect the cruise control. However, modern cruise controls are fully electric and in most cases will not be affected by a vacuum leak if the check engine light is not illuminated.

Although many people may think that the cruise control system is unimportant and not worth spending money to repair, the problem can be caused by a faulty part that will affect the engine’s performance or durability. Therefore, it is best not to ignore the problem if your cruise control is not working without first diagnosing the car properly.

If your cruise control still isn’t working after trying all the tips in this article, it’s probably time to take it in for a professional opinion from a mechanic. It may be a more serious problem that requires replacement parts or repairs. In the meantime, drive safe and enjoy the open road!

Learn more:

• Brake Lights Not Working But Tail Lights Are? (How to Fix)
• Tail Lights Not Working But Brake Lights Are? (How to Fix)
• Brake Lights Stay On? (5 Causes & How to Fix it)

Categories: Electric , Troubleshooting

Related Posts

Latest Posts

• The Best & Worst Years Of Ford Explorer
• Best & Worst Years Of Toyota Corolla
• Best & Worst Years of Toyota RAV4
• When Should Your Child Switch To A Forward-Facing Car Seat?
• The Best & Worst Years Of Toyota Camry
• I Accidentally Put Premium Gas In My Car, What To Do?

• Why is my Cruise Control not Working? [14 reasons]

14 Reasons Why your Cruise Control may NOT Be Working

The reason for your cruise control not working could be as simple as a blown fuse to really complex electrical problems. Defective switches, sensors, and even “check engine” light, all could contribute to this problem.

If you like to travel and own a car fitted with cruise control, you know how comfortable it can be to maintain a constant speed! When a cruise control system gets damaged, it is just as annoying as it is dangerous.

Cruise control is connected to several components of the car, and when it fails it can mean that something could be wrong with the CC itself. It could also be a signal that something wrong is happening with any other component of the car.

Why is my cruise control not working?

In this article, I am going to show you the main reasons why your cruise control may not be working (from the simplest to the more complex ones):

Reason #1. Bad or blown fuse

The cruise control’s circuit (like many other electronic components of your car), is protected by a fuse that will blow to protect the system from short circuits and overloads. If your vehicle’s cruise control fuse is blown, the system will stop working.

You can replace the fuse with a new one of the correct amperage, according to your vehicle’s owner manual. If the new fuse doesn’t blow again, everything will be ok; if the fuse blows again, you have to keep searching for what is making that fuse blow.

Reason #2. Burnt brake lamp

Some cruise control systems are disabled when the brake lamp is blown. Check your brake lights. If you find a burnt brake light, just replace it and test the system again.

Reason #3. Defective brake light switch

A defective pedal switch can also make your cruise control stop working. Remember that all cruise control systems are automatically disengaged as soon as the brake pedal is pressed down.

If the cruise control didn’t stop working when a fault in the brake light or brake pedal switch is detected, it could be dangerous; that’s why the CC control unit constantly monitors the status of this switch.

Reason #4. Clutch pedal switch deactivation (for manual transmission vehicles)

Cruise control is deactivated when the clutch is pressed by the driver in manual transmission cars. The CC control unit monitors this switch as it does the brake light switch.

Reason #5. The vehicle speed sensor is not working

A vehicle’s cruise control needs to be able to determine the vehicle’s actual speed. This enables the system to determine how much throttle needs to be applied in order to keep a certain speed, among other things.

The speedometer speed sensor is not always the sensor used by cruise control. Some systems rely on the ABS speed sensors, others do an average and some have a dedicated speed sensor.

If the system can’t detect the vehicle’s speed or detects a problem with the speed sensor, it will stop working.

Reason #6. Faulty throttle body or accelerator pedal

In modern engines, the throttle body is driven electronically by the engine control unit (ECU), and the accelerator pedal works like a potentiometer. The processor managing the cruise control system will act as the accelerator pedal, sending more or less voltage to the throttle body to open or close the throttle body’s butterfly valve.

If there is a problem with your vehicle’s throttle body, your cruise control won’t work.

Reason #7. Check Engine light is “ON”

If your vehicle instrument panel has the “Check Engine Light” ON and the fault stored in the ECU’s memory is related to some component vital for the cruise control system, you will not be able to use your cruise control until you have fixed that problem.

Reason #8. Faulty steering wheel’s spiral cable/clock spring

The spiral cable connects all the switches from the steering wheel (in case your steering wheel has switches) to their respective modules. This includes the connection of the driver’s airbag.

These wires (also called clock springs) are prone to get cut. A faulty spiral cable may have an open circuit making it unable to reach the vehicle’s cruise control module (CCM).

Reason #9. Bad Cruise Control Switch

Your vehicle’s cruise control switches have internal contacts that wear out. If that happens, the switches won’t be able to contact the CCM.

Depending on which buttons are faulty, your whole cruise control can stop working or just some functions won’t work.

Reason #10. Electrical problems with different modules and wiring

Modern cruise control systems use electrical and electronic components, and they are connected to other modules and systems of the vehicle. Some of these systems are the ECU, ABS, and/or Stability Control Systems like ESP.

The CCM makes a check of these systems once the key is switched to ON, and if some of these components are not working in optimal conditions, the CCM won’t engage. If none of the above items seem to be the problem, the vehicle needs to be taken to a professional who can perform a full scan of all the components, check that all the voltages, wiring harnesses, and connectors are ok.

The professional is going to detect if there are any connection problems between modules and will be able to find the reason why the cruise control is not working.

Reason #11. Dirty or faulty camera or sensor (only for vehicles fitted with adaptive cruise controls)

Newer vehicles have adaptive cruise control systems. These devices not only keep a fixed speed by the driver; they also can detect other vehicles ahead and behind and are able to keep a safe fixed distance to avoid collisions.

Some of these new systems have laser sensors while others have cameras to calculate the right distance to follow considering the vehicle’s speed and acceleration. Any problem with the sensors will prevent adaptive cruise control from working.

Problems with older cruise control systems

Before electronic injection and electronic throttle bodies, some cars had the cruise control function. In fact, the first cruise controls were introduced in the early 1950s.

These electromechanical cruise controls are pretty simple. They have a vacuum actuator connected to the throttle linkage that opens and closes the throttle to maintain the vehicle’s speed.

In early injection cars, the throttle linkage was replaced by a cable. Some common faults of these old cruise control systems are:

• A faulty vacuum actuator. Vacuum actuators have a diaphragm inside that can break. Any vacuum leak will lead to failure.
• Faulty vacuum control solenoid. It can prevent the actuator from operating normally.
• Broken throttle cable. If the throttle cable or linkage is broken, it needs to be replaced.

I hope you enjoyed my guide to cruise control problems. Even though it doesn’t explain how to fix your cruise control, it gives you an idea of where to start looking if you are going to do it yourself.

Now you will have an idea about how the system works and what are the possible reasons why it’s failing (in case you have to take your vehicle to a shop to be repaired).

Attention! This article is for informational purposes ONLY and is NOT a replacement for professional advice! ALWAYS consult your local specialist for an appropriate solution to your problem. All statements, prices, contact information, recommendations, and reviews contained herein came from sources that we believe to be reliable, but the accuracy or completeness thereof is not guaranteed. Please contact the service provider for complete details and updates.

I always Know and admit that even though I went to school for ABR grad. In 1994 3.36gpa still have go go back to school for upgrades due to vehicle advancement but I still learned alot although I am dealing with an 05 f150 stx which has more recalls then a auto parts store where the employees don’t know a inerta. Switch from an ignition switch ,thanks for the information

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

Privacy Overview

Automated page speed optimizations for fast site performance

Fixing Faulty Cruise Control

Alarmingly, the speedometer needle steadily winds down from 75 mph toward 50. Just as you uncurl your feet and try to accelerate back to traffic speeds, the vehicle downshifts with a lurch and abruptly climbs back to over 80 mph. So you tap the brakes and disengage the cruise control to avoid a conversation with one of the many law enforcement officers lurking behind every other billboard. Toggling the Resume switch settles things down, holding to a legal speed on both the uphill and downhill sections of the interstate. The kids in the back seat have stopped threatening to throw up, too. Then you look in your mirror 20 miles later and see the lights. Red and blue flashing lights. You're doing over 85 mph and, odds are, Smokey isn't going to believe you have the cruise set to 70. Time to find out why your cruise control has a mind of its own.

IT'S NOT A BUG, IT'S A FEATURE Does your cruise control fall out of engagement partway up steep hills? Actually, it will normally drop out if the engine has to work too hard, mainly because after a while there isn't enough vacuum left to pull in the servo after sustained near-wide-open-throttle. You'll just have to put your foot into it. Downshifting helps.

Does your Japanese car not remember the set speed after tollbooths? Unlike most American and European cars, some Toyotas and Hondas are designed not to remember their set speed if the vehicle speed falls below 25 mph, and you're supposed to accelerate the vehicle to your set speed and hit the Set button again. Annoying, but that's the way they were designed.

Do you have to ride the brakes on longer downhills to keep from building up excess speed? That's normal too. The cruise control only has authority to reduce engine speed to idle. It doesn't activate the brakes. Modern cars, in an attempt to improve mileage, have very tall gear ratios, low-friction engine designs, low-rolling-resistance tires and optimized aerodynamics. That long downgrade outside of town may have accelerated your '60s-era Pontiac to only a couple of miles per hour above legal. But, it may well propel your new economy car to blatantly illegal velocities unless you intervene by braking or downshifting.

WHAT'S THAT HISS?: Most common cause of erratic cruise control? Vacuum leaks caused by deteriorated hoses.

SMOOTH AND STEADY Cruise control on your vehicle is a terrific device. It substantially reduces the driver's workload on longer trips, and can save substantial amounts of fuel and expense over the life of the vehicle--until it stops working.

We'll get to the scenario of not holding a steady speed later, but here are a couple of things to check immediately if the cruise control is on strike.

Does the Cruise icon on the dash light up when you turn the switch on? Duh. Check the fuse. You may need to look in the owner's manual to see which one if it's not tagged on the fuse box cover. An aftermarket cruise may have an inline fuse holder in the wiring to the controller.

If there is power to the system, the next check is the brake lights. Brake lights? Yup, cruise controls have a switch to toggle them off when you touch the brake pedal, and many use the same switch as the brake lights. If one of the brake lights has failed, the cruise control thinks the brakes are on all the time and won't come on. Same result if the switch is incorrectly adjusted or broken or jammed. Wait, there's more--if your vehicle has a manual transmission, there's a similar switch on the clutch pedal. You may need to break out a test light or multimeter to verify the function of this array of switches. These switches usually are normally closed switches, and close their contacts when the pedal is depressed. We've seen several cases of intermittent cruise control dropout caused by a brake light switch that was adjusted very tight. Any small bump would jiggle the brake pedal down far enough to toggle the brake lights on for a brief instant--long enough to shut down the cruise. Adjusting the switch to specs (usually so the brake lights come on after the pedal travels 1/2 in.) fixed it.

Once you verify all of these things, it's time to look for more subtle causes. Check underhood. Inspect the linkage between the cruise control actuator and the throttle. It may be as simple as a toilet-tank bead chain or a separate throttle cable with its own actuator cam to the throttle body. Look for disconnected or damaged wiring to the controller or actuator, particu-larly if it's an aftermarket system, which may have been installed by someone with poor mechanical skills.

Another obvious failure point is the vacuum line to the actuator. If it has fallen off, there's no vacuum to the actuator and no force can be applied to the throttle. We'll get ahead of ourselves here and mention that a vacuum line that looks fine may have a subtle leak caused by aging, brittle rubber or connections that don't seal well. A lot of the cruise controls we've seen with issues in regulating their speed correctly are fixed by simply replacing all the vacuum lines between the servo, vacuum reservoir (if there is one) and the intake manifold vacuum supply.

WHOA, NELLIE!: If your brake light switch is incorrectly adjusted, your cruise control may not lock in. A burned-out brake light can do the same.

WHAT'S THIS THING?: The cruise control servo motor could be anywhere in the engine compartment.

CONTROL ISSUE WITH YOUR SERVO There are two main components of the cruise control system: the controller and the servo.

The controller integrates all the inputs and tells the servo how far to actuate the throttle plates. Normally, there is no way you can service this item, so if you trace a problem to the controller, you'll have to buy a new one. A bad controller probably will require a service manual for specific diagnostics. You'll also need a scan tool to access any computer trouble codes to boot.

The servo does the work of moving the throttle blades to speed up the vehicle. Conventional systems are actuated by manifold vacuum. Check the linkage from the servo to the throttle to ensure it's properly hooked up and not binding or sticky. Inside the servo is a diaphragm that moves to pull on the linkage. Some older systems, used on cars or trucks that don't have throttle-position sensors, may have a rod that moves in and out of a magnetic coil to tell the controller the throttle position. There are also two electrically operated solenoid valves. One valve admits vacuum to the diaphragm chamber to add more throttle. The other bleeds air back into the chamber to reduce throttle. Normally, they will never be open at the same time, so if one is sticky or leaking, cruise control operation will be erratic at best. Check for leakage with a handheld vacuum pump. A leaky valve may benefit from a quick shot of silicone spray.

Diesels and some late models may use a servo that is completely electrical. These usually are mounted on the fenderwell or firewall, and are connected to the throttle by a second throttle cable. Other than keeping the cable lubricated and properly adjusted, there's not much to fiddle with. As always, check the shop manual for specifics on your vehicle.

Many late-model cars have throttle plates connected directly to an actuator controlled by the engine management computer. There is no physical connection between your right foot and the throttle blades (Scary, eh?), and there may or may not be a separate cruise control servo or controller.

HOW FAST WAS I GOING, OFFICER? If you still have no engagement, there may be an issue with the cruise control's speed input. Modern cars use information from the ABS's vehicle speed sensor (VSS) because the engine-management computer needs to know road speed. If your Check Engine light is on, the cruise may not work, especially if the VSS is malfunctioning. Older vehicles may use speed information from the speedometer. Aftermarket systems may resort to a ring of magnets clamped to a driveshaft or axle shaft, with a magnetic coil positioned nearby. If the magnets have fallen off or the coil has been smashed by a rock or road debris, there's no speed data for the controller.

URBAN LEGEND The legend has been related to us by all manner of people, including a couple of state police officers. Using the cruise control in rainy or slick conditions will make your car speed up uncontrollably, until you lose control and crash. It's a myth. Engaging the cruise will not make the car speed up. The cruise will attempt to maintain a steady speed. If the wheels lose traction and the car starts to slow down, the cruise will speed up the engine to attempt to accelerate back to the set speed. This will make the drivewheels spin more briskly. The vehicle speed will go slower, regardless of how furiously the wheels spin. If you have a rear-wheel-drive car, the effect is to destabilize the vehicle, and you probably will spin out unless the vehicle regains traction in a reasonable length of time. A front-wheel-drive car with spinning tires will attempt to continue in a more or less straight line--which will make steering control dodgy at best.

Heavy rain or snow makes use of the cruise control inadvisable, but such conditions certainly won't make your car accelerate to ludicrous speeds while you hang on for dear life. If the cruise is engaged and you perceive a loss of traction, the best bet is to tap the brake to disengage the system, and then add just enough throttle to maintain steering until the vehicle slows down to a more appropriate speed.

WHERE'S THIS THING?: Speed sensor may be buried under the dash near speedo head.

SUCK IT UP: The vacuum reservoir provides an added source of vacuum for those long uphill grades.

.css-cuqpxl:before{padding-right:0.3125rem;content:'//';display:inline;} Cars .css-xtujxj:before{padding-left:0.3125rem;content:'//';display:inline;}

The Best Microfiber Car Cloths for Your Vehicle

The Best Car Cup Holder Adapters in 2024

How To Wash Your Car

The Best Car Tools to Keep Up With Maintenance

How to Replace Your Car’s Brakes

How to Change Your Oil And Filter

The Best Carports for Weather Protection

The 40 Best Car Toys for Kids in 2024

The 6 Best Car Trash Cans for Collecting Debris

The 5 Best Cordless Power Washers

The 2024 Nissan Rogue Is Making Its Great Escape

Mercedes-Benz of Scottsdale

Official blog.

Why isn’t my cruise control working when I drive?

Cruise control is a vital luxury that many car drivers would hate to go without. So, if you’re cruise control suddenly goes out on you, this is provably a fix that you want to get taken care of right away. So, why isn’t your cruise control working, and how do you fix it? Let’s take a closer look.

5 Reasons why your cruise control stops working

If you’re cruise control isn’t working, it may not even be the fault of this technology. As you know, if you step on the brakes, your cruise control stops working. So, if there’s something wrong with your brake light switch or your brake lights , your cruise control may think you’re applying the brakes and turn itself off.

Likewise, the cruise control has a control switch , too. So, if something is worn out or damaged, then it stops working.

Engine or transmission issue: if you drive a newer year model you’re cruise control may turn itself off if you have an engine or transmission issue. So, if you see your engine light come on and all of a sudden your cruise control doesn’t work, then it may not be your cruise control having issues

Spiral Cable : If you have a bad spiral cable in your steering wheel, your cruise control may not turn on, as the control switch for the cruise control can’t communicate with the cruise control itself.

Electrical issues : your vehicle has many connectors and electrical components. If one of these goes on your cruise control, this can cause the cruise control to stop working.

Read more: Tips on how to get rid of wildlife in your car

How to fix a cruise control that isn’t working

While you can potentially identify the reason why your cruise control isn’t working, it’s best to contact your service & maintenance team to fix the issue. Thankfully, you have a reliable team close at hand.

Come on over to your friendly Mercedes-Benz of Scottsdale to find a trustworthy service and maintenance team that will be happy to help you with all of your automotive needs. Not only can we fix little things like your cruise control, but we can also take care of vital engine repairs, such as transmission, spark plugs, catalytic converter, etc. So, if you’re car needs a little TLC, we encourage you to give our team a call straight away.

A Guide to Choosing the Best Oil for Your Mercedes-Benz in Scottsdale, AZ

Where can i get the wipers of my mercedes-benz checked in arizona, where can i get muffler repair service for my mercedes-benz in scottsdale, az, where can i get the ac of my mercedes-benz repaired in arizona  .

Cruise Control not Working (Diagnosis and Troubleshooting)

What makes cruise control not work.

Bad brake pedal/light switch — This means communication between you, cruise control and the car is interrupted, and you can’t have immediate manual control of the car.

Bad fuse — Fuses blow to protect the electrical system. Cruise control fuses will do the same, to protect the system and circuits in your car the fuse will break and then need repairing.

Failing speed sensor — Speed sensors are important in cruise control because your car needs to remain at the same speed consistently. Broken speed sensors will affect more than cruise control and need to be serviced urgently

Bad actuator vacuum, hose, or cable –The actuator vacuum is what connects and activates the throttle control. The fault may be with the hoses in the vacuum actuator or the cable linking the system together.

Symptoms of bad cruise control switch

• Symptom 1 — brake pedal does not disengage cruise control

There’s a switch fixed to the bases of the brake pedal and if cruise control does not deactivate when braking then it’s a sign that this switch is faulty.

• Symptom 2 — Hissing noises are heard from under the dash.

The cruise control switch is a vacuum system and for some vehicles, it is mounted near the brake pedals under the dash. If you can hear hissing, it could indicate that the switch or one of the switch’s vacuum hoses is broken.

• Symptom 3 — The cruise control switch/button itself does not work

When trying to turn on the function or while cruising it turns off, this is an indicator of a faulty switch and can be related to wiring issues or the above (1-2) symptoms

• Symptom 4 — A blown fuse

A blown fuse could be a simple error and fix. The switch circuit or fuse may just need to be replaced for the problem to resolve.

Possible Cruise control failure Scenarios

1. Cruise control not working after battery change

• Possible cause — This differs from vehicle to vehicle and among brands. Some drivers’ cruise control malfunctions after jump-starting their battery, and this is because the battery is still discharged. Newer cars have many electronic systems, and most are powered by the battery. So, if the battery is discharged or low-powered, the electrical cruise control system can be affected.
• Solution — Putting your battery on a trickle charger (2-5 amp) for 12 hours or driving on cruise for a couple of hours may resolve this issue.

2. Cruise control turns off while driving

• Possible cause — Damaged speed sensor or actuator, these two could be internally malfunctioning and causing the cruise control to disengage without input from you.
• Solution — Have a technician or mechanic run a diagnostic with the speed sensor and check the actuator hoses and cables.

3. Cruise control works intermittently

• Possible cause — this may relate to the brake pedal switch. If cruise control is intermittently disengaging, it could be a wiring issue with the switch.
• Solution — Have the brake pedal to cruise control switch investigated by a mechanic or technician and determine if there is a faulty wire to blame. You may need to have the switch or some of its parts replaced.

4. Cruise control turns on but will not set

• Possible cause — The brake pedal switch may be the issue. The brake pedal deactivates cruise control and if it is stuck in the open position, it may cause the cruise control to not engage or set properly.
• Solution — Ask your mechanic or technician to check for this issue specifically in their diagnostic and service.

5. Cruise control turns on by itself

• Possible cause — There may be a failure with the Electronic Control Module (ECM) which manages the actuators or Electronic Control Unit (ECU) which controls the speed in your cruise control
• Solution — You could attempt to reprogram the ECU and ECM if you have the computer tools, otherwise take it into a trusted mechanic or technician.

There are many helpful forums run by mechanics and amateurs:  These are always great for solving those specific problems you might experience.

When CC does not set: https://mechanics.stackexchange.com/questions/34795/cruise-control-will-not-turn-on-cannot-be-enabled-nor-set

When CC is faulty after battery change: https://www.vwvortex.com/threads/help-cruise-control-not-working-after-dead-battery.4464553/

For cruise control and other general repairs, watch this channel: https://www.youtube.com/channel/UCf2f4MeZzSksVMe1z3Lp3hw

Can cruise control cause check engine light?

When the check engine light or MIL (Malfunction Indicator Light) is on, the cruise control light may blink to signal that cruise control has been disabled. This is a safety control as the vehicle is programmed to not go on ‘autopilot’ should the engine or mechanical issue relate to the cruise control systems. If the error or fault is with the cruise control systems, then the MIL may be lit for that as well.

How much does it cost to fix cruise control malfunctions?

• For switch repair (parts and labour) it’s estimated at $125- $350
• For fuse repairs, it could be up to $10 to buy the fuse and replace it yourself in a few minutes — there are many helpful YouTube tutorials on simple car repairs like this one.
• For actuator repairs, some cost more than $700
• Therefore, it’s important to know WHAT the issue is to get an idea of HOW MUCH it will cost you.

Does cruise control malfunction trigger the check engine light?

The function of a check engine light or MIL (Malfunction Indicator Light) is to communicate engine or mechanical failures in your vehicle to prevent an accident on the road. The MIL can be lit for simple reasons like the gas cap is loose. Should your CC system fail or run incorrectly, the MIL could light up. Often when there are other failures or engine faults, the MIL will light and the cruise control with a flicker to signal it has been disabled for safety reasons. Once the cruise control or other issues are fixed, all the lights should go back to being turned off.

Author: Dave Johnston

Related articles.

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

Recent Posts

MyCarMakesNoise.com

Copyright © 2024 My Car Makes Noise

• Forum Listing
• Marketplace
• Advanced Search
• Mercedes-Benz Coupe/Convertible Forums
• C209/A209 CLK-Class

Cruise Control Inoperative

• Add to quote

Driving our 2008 CLK550 from NY to FL over the course of several days. Car has 71k miles on it, but rarely driven for these long of stretches. About 1/2 way into the trip I got a "Cruise Control Inoperative" message while driving along at highway speed. The error does not appear to be going away despite a couple of vehicle re-starts. The drive has been quite rainy, don't know if that may have an influence on cause for the error. I searched through the forum & it appears that other members have had ESP control failure problems in conjunction with cruise control fails, but that is not my case (yet...). Just wondering if it might be something simple like a blown fuse, or if it is more likely a wheel sensor going bad. Thanks in advance....  

If it's not an ESP error, it could be a transmission problem. Mine starting doing this right before the infamous speed sensor failure, requiring conductor plate replacement by the dealer.  

Doing a bit of reading on this, it sounded like it applied to earlier models. Is that conductor plate failure a problem with 2008 CLK's?  

Yes, it can happen on a MY2008. I am not sure when they finally fixed the issue wit the revised conductor plate, but I am guessing in 2009 or 2010. I'd scan the TCU for codes (a generic OBDII scanner won't do it - use a scanner that can read MBZ proprietary systems).  

• ?            
• 703.1K members

Top Contributors this Month

A .gov website belongs to an official government organization in the United States.

A lock ( ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

• Vessel Sanitation Program
• Stay Healthy on Your Cruise
• Meetings & Announcements
• Vessel Sanitation Training
• Data Summary
• Public Health Resources
• Addressing AGE on Cruise Ships

Celebrity Summit May 2024

At a glance.

Learn about the gastrointestinal illness outbreak on Celebrity Cruises ship Celebrity Summit in May 2024, including outbreak details and actions taken in response.

Outbreak details

Cruise Line: Celebrity Cruises

Cruise Ship: Celebrity Summit

Voyage Dates: May 24–May 31, 2024

Voyage number: 58044

Number of passengers who reported being ill during the voyage out of total number of passengers onboard: 68 of 2,264 (3%)

Number of crew who reported being ill during the voyage out of total number of crew onboard: 5 of 943 (0.53%)

Predominant symptoms: diarrhea and vomiting

Causative agent: norovirus

Actions in response to the outbreak

In response to the outbreak, Celebrity Cruises and the crew aboard the ship reported the following actions:

• Collected stool specimens from gastrointestinal illness cases for testing.
• Isolated ill passengers and crew.
• Staged disembarkation for active cases to limit the opportunity of illness transmission to well guests.
• Sanitation of terminal and transport infection control procedures.

VSP remotely monitored the situation, including review of the ship's outbreak response and sanitation procedures.

Tips for healthy cruising

Learn how passengers can protect themselves .

More information

Gastrointestinal illness is a commonly used term for acute gastroenteritis (AGE). Cruise ships report cases that meet our case definition for AGE. We define a reportable case of AGE as

• Three or more loose stools within a 24-hour period or what is more than normal for that person OR
• Vomiting along with one of the following symptoms: diarrhea, muscle ache, headache, abdominal cramp, or fever.

Case totals

Cases reported are totals for the entire voyage. It does not mean all people are sick at the same time, such as when they arrive or leave a port or ship.

The Vessel Sanitation Program helps the cruise ship industry prevent and control the introduction and spread of gastrointestinal illnesses on cruise ships.

For Everyone

Public health.