2012 dodge journey warning lights

Dodge Journey Dashboard Warning Lights (All Models 2009 to 2020)

Welcome to the ultimate guide to all dashboard symbols, warning lights, errors and faults for the 2000 to 2020 Dodge Journey. This will assist in troubleshooting, diagnosing and solving common automotive problems with this specific car.

Please note: This guide covers every single possible symbol/warning light for ALL model variations for Dodge Journey, including standard, premium and top-of-the-line models, plus variations in body shape. While this guide does cover your specific vehicle , your car may not have all the symbols featured on this list.

Dodge Journey Symbols and Warnings Guide

There are 25+ possible lights that may illuminate for a variety of reasons.

While this guide is helpful, please refer to your owner’s manual after reading through this list.

Dodge Journey Engine Fault

There are hundreds of reasons why the check engine warning fault light comes on, and only your dealer or mechanic is qualified to address this.

Common reasons include a loose fuel cap, excess vibration, a blocked cylinder, a bad fuel mix, excessive heat and half power.

This may also highlight an issue with your transmission.

Dodge Journey Check Engine Oil

This means your engine oil is running low or has been completely drained. Your engine may have an extensive oil leak and a mechanic will be required urgently.

At this stage, it’s not recommended that you drive your vehicle.

Dodge Journey Attention / Warning / Fault Detected

Either of these two lights will illuminate to get your attention to other dashboard warning lights and symbols.

These lights can also mean that the handbrake is engaged.

Dodge Journey Battery

This means your battery has low voltage and may need a replacing.

Should you choose to drive your vehicle with a faulty battery, you risk losing power to your battery at high speeds.

Many mechanics will prefer to visit your home to replace your car’s engine battery, rather than have you drive to them.

Dodge Journey Press Foot Brake

This symbol is your Dodge Journey telling you to press the foot brake.

This is required before starting the engine and moving the vehicle out of Park.

Dodge Journey Handbrake Engaged

Your handbrake is engaged.

This can be disengaged by hand, or your vehicle may have a handbrake that is disengaged with your foot.

Dodge Journey Airbag Fault

This means your driver’s side or passenger side airbag has a fault and may not deploy when required. However, it’s quite common for this light to illuminate due to a faulty sensor, rather than a faulty airbag.

Take your vehicle to your mechanic for inspection as soon as possible.

Dodge Journey High Radiator Coolant Temperature

This symbol represents excessive heat from your engine’s radiator. If ignored, you risk overheating your engine very quickly.

Common reasons are a low coolant level and a leak in the radiator.

Call or visit a mechanic immediately.

Dodge Journey Parking Sensors

This symbol represents the front or rear parking sensors. You will also hear an audible beep as you get closer to a wall, pole, tree or other object when reversing.

Dodge Journey Bulb Not Working

This means one of your driving lights has stopped working and requires either a bulb replacement or fuse replacement.

Dodge Journey Low Beam Lights On

This means your front standard driving lights are on.

These lights are used for 99.9% of driving.

Dodge Journey High Beam Lights On

This means your front high-beam driving lights are on.

These lights are used for 0.01% of driving and typically for country roads late at night. Fines can apply for use of high beams in dense residential areas. Do NOT use high team driving lights within 400 metres (1,000 feet) of an oncoming car.

Dodge Journey Automatic Low Beam Lights On

This means your front automatic standard driving lights are on.

These will illuminate by themselves on dusk, when entering tunnels and in other low light situations.

Dodge Journey Automatic High Beam Lights On

This means your front automatic high-beam driving lights are on.

Please be wary that these lights do not turn themselves on automatically around other cars.

Dodge Journey Automatic Lights Malfunction

Dodge Journey’s come with automatic lights, however, these can malfunction.

This is often an issue with the front low-light sensor. You may continue to drive and simply use your normal on/off headlight function until you visit a mechanic.

Dodge Journey Glow Plug Indicator Symbol

This is the Glow Plug Indicator symbol, which is found only in diesel-powered variants of Dodge Journey. Diesel engines require heat in the cylinders to operate, which is supplied initially by its glow plugs when the engine is freezing cold.

When illuminating green, this is operating perfectly but when yellow, a fault may exist.

Dodge Journey Vehicle Is In Park

This means your vehicle is in Park.

Dodge Journey Hood / Bonnet Is Open

While your front hood/bonnet may appear closed, it may show open on the sensor.

Dodge Journey Front Fog Lights Enabled

This means your Dodge Journey front fog lights are engaged. A similar symbol exists for the rear warning lights.

Note: In some areas, it is illegal to use fog lights when it isn’t foggy. Please check with your local authority.

Dodge Journey ABS System Fault / ABS System Off

Your vehicle’s ABS system has a fault and may not engage under heavy braking.

Please visit a mechanic as soon as possible.

Dodge Journey ECO Mode On

ECO mode in a Dodge Journey is an optimum driving mode.

Your throttle will not respond favorably to performance driving.

Instead, your fuel economy will be at its best, hence the term ‘Eco’.

Dodge Journey Truck / Boot Open

While your rear trunk/boot may appear closed, it may show open on the sensor.

Dodge Journey Front Radar Engaged

This means your front sensor is engaged.

This feature provides autonomous braking and adaptative cruise control.

Dodge Journey Lane Assistant On

This means your lane-keeping assistant is on.

This feature allows your vehicle to remain straight within its lane.

This may only engage above 40km/h or 25mp/h.

Dodge Journey ESP / ESC Engaged

This means your Dodge’s Electronic Stability Programme (or Electronic Stability Control in some countries) has been engaged.

This typically engages on wet, muddy or icy roads.

Dodge Journey Check Brake Fluid

This means your brake fluid has become low and may require topping up.

Dodge Journey Check Brake Pads

This means your brake pads have become low.

This may be difficult to check and may require visiting a mechanic as soon as possible.

Dodge Journey Steering Wheel Locked

This means your steering wheel is locked.

This is an anti-theft symbol that flashes when your vehicle is locked.

Dodge Journey Service Due Soon

This means your vehicle is due for servicing soon.

Your mechanic may have programmed an alert within your car’s computer to illuminate this symbol upon crossing a certain odometer reading.

Dodge Journey Heated Seats

This means your heated seats are on.

The number of vertical lines represents the level of heat.

Dodge Journey Cruise Control Activated

This means your cruise control has been activated and is ready to use.

However, your cruise control will not be on. It’s simply ready to switch on.

Cars often use 2-buttons to avoid accidentally turning on cruise control.

Dodge Journey Check Wheel

This means you have an issue with your wheel.

This isn’t the rubber tire but the wheel itself.

Issues include alignment, steering and balance.

Dodge Journey Heated Windscreen

This means your windscreen is being heated to melt frost or ice.

This may turn itself off automatically.

Dodge Journey Air Suspension Fault

If your Dodge Journey has air suspension, then this symbol represents a fault.

This could be a deflated rear suspension air bag, an air leak or a sensor issue.

Dodge Journey Tire Air Pressure Fault

This means your tire pressure is either too low, or the sensor has faulted.

This requires calling or visiting your dealership as soon as possible.

Dodge Journey Intermediate Windscreen Wipers On

This means your automatic windscreen wipers are on. No action is required.

Ultimately, your car is trying to tell you something. You should consult your owner’s manual and have your car inspected by a qualified mechanic as soon as possible.

Symbols Have Different Colors

Much like traffic lights, the color of your dashboard symbol light is just as important as what it means. The lights can also flash to draw your attention to a more severe and time-sensitive issue.

When a Dodge dashboard warning light is green or blue, they are simply telling you that one of your car’s features is being used, or has been activated. No action is required at this time.

When a light is yellow, your car is trying to tell you that a less common safety feature of the car is being used (such as stability control on wet roads), a mild fault has been detected or a repair may be required. If you’re unsure, you should seek the services of a mechanic or dealership as soon as possible.

Orange or Red

If the dashboard on your Dodge is orange or red, this can be a signal that your vehicle is experiencing a problem that needs urgent attention . You MUST call or visit your dealership or mechanic immediately.

This dashboard symbols guide is for entertainment and informational purposes only, and does not replace seeking professional advice from a certified technician or expert mechanic. Please consult with a certified technician or mechanic if you have specific questions or concerns relating to any of the topics covered herein. Under no circumstances will DashboardWarningsLights.com be liable for any loss or damage caused by your reliance on any content on this website.

Joshua Lee is the writer, editor and owner of DashboardWarningLights. Joshua has a deep obsession with the automotive industry, for both passenger vehicles and trucks. When he isn't writing or driving, he enjoys exploring in the great outdoors!

DASH-LIGHTS.COM

Dashboard Warning Lights Explained

Dodge Journey Dashboard Warning Lights

64 thoughts on “ dodge journey dashboard warning lights ”.

My dash board lights only goes off for like 10minutes and then comes back on permanently after turning off the engine and locking the car doors. this drains my battery

I got a warning light that I can’t find in my manual or on line. It looks like a screw in the side of the vehicle. Can you tell me what it means?

Hello Patricia, Are you sure the car and screw warning light is not a loose gas cap symbol?

I checked these on mine but did not affect car with large screw hovering.

I just got that light today…is it the gas cap

Put antifreeze in the car gauge says the oil temperature is rising the transmission fluid temperature is rising and the coolent temperature is rising and says 5470 engine hours what does this mean

Hi Wanda, How old is the existing antifreeze? If it’s several years old, it may require flushing, else there may be sludge build up resulting in the system getting blocked. Transmission systems can also make use of the car’s cooling system and can overheat if there’s a problem. Also check your char’s water pump. The engine hours is referring to how many hours your engine has been in operation over its lifetime.

Patricia I had the dame this last week and even the mechanic had never seen it I checked the gas cap, took if , screwed it in again, but no change. Had the lugs tightened on wheels though he said they were fine= zi have NO IDEA. It bothers me that it’s not in the manual

2014 Dodge Journey: 3 warning lights came on simultaneously. Oil which is full, tired which are filled to spec. and eve light. What causes this and how do I fix it?

Hi Tom. Rather than ‘eve light, did you mean ABS light? Sounds like sensor issues. I would concentrate on the oil light initially as this is the most serious and have your engine pressure checked. If it’s good, it may be the oil pressure sensor.

My 2009 Dodge Journey’s instrument panel completely lights up when shifting from 1st to 2nd. You can feel a slight jerk and click. Tranny works fine but the dashboard is completely lit up. I already reset the dashboard but it comes on immediately when shifting from 1st to 2nd.

Round red light came on three times went out each time what is this red dot panel with rpm’s

Hi Yolanda. I think it’s the vehicle security warning light. Have you changed or disconnected the battery?

I have a 2009 Journey. Sporadically, the ESC light will come on, and the car starts running very rough….almost to the point of stalling. However, if I keep a steady flow of gas, it doesn’t stall on me. Do you know how the gas and ESC error light would be related causing the car to run so badly? Thank you!

Hi Amy, Part of the ESC (Electronic Stability Control) system is to cut engine power and can also apply braking. This helps with traction (preventing wheel spin), oversteer and understeer. If the system is faulty, it could be engaging when it’s not supposed to and giving you the rough engine and problems accelerating. This could be something as simple as a wheel speed sensor that’s at fault, or the ESC module, steering angle sensor.

On my dashboard. Red light came on.and i can’t find the red light symbol.i have a 2010 dodge journey.i have look up the symbols on my phone and i can’t find that symbol.

Hi Loretta Can you describe the light?

I’m having a similar problem as Amy. Sometimes my ESC light will come on and it says OFF though. Basically ESC OFF it shows the image, but it says OFF. It happened today. I turned on the car and the light came on and I had to get in the interstate and I was going 70+MPH and whenever I would let my foot off the gas and the vehicle would stutter and feel like it wanted to stall. The MPH would begin to drop and I wasn’t able to increase by speed. It would drop to about 60 MPH and then I would be able to increase by speed again..I have a 2011 Journey.

I am having the same problem…did you ever figure out how to fix it??

2018 Dodge Journey check engine light and it woo t switch gears. It will jerk really hard then it won’t switch gears

I have a flashing “Dodge” symbol that flashes then remains on for a short time. The tipm has been replaced. Could it be a reset is needed?

What does red ‘Back’ light mean

what does it mean when the letters PSI come on?

On my 2010 Dodge Journey. The Eps light is staying on

My dodge journey yellow light has just come up. Although today I’ve had new tyres and rims fitted have you any idea as to why if so any help will be appreciated thanks

Hello Kelly, I assume you mean the tyre pressure warning light? The tyre pressure light coming on after having new tyres fitted is usually a sign that a sensor has not been fitted, not been fitted correctly or damaged during the tyre fitting service.

I have a stupid question! Do I turn on the slippery car symbol when I’m driving in the snow?

Hi Janie, No, don’t touch it, it will automatically be on already. If you press the button so that the slippery car symbol illuminates, you’ll be switching the system off. On most cars it’s called electronic stability control (ESC) or something similar. ESC comes on automatically each time you start the car.

If you happen to get stuck in snow and can’t get out, you might need to rock the car backwards and forwards. In this situation, you press the ESC button (slippery car symbol), or the traction control button to deactivate traction control. By leaving traction control on, it’ll stop or reduce wheel slip, but if you’re stuck in snow, you want wheel slip to help free your vehicle. Once you’re free from the snow, press the button again to switch on ESC.

Hello, I have a 2016 journey and I get the ETC and the ESC indicators on. Usually I pull over, turn off the car and wait a few seconds but now it’s happening more often. What is this and how can I fix it?

Hello, my ETC and my ESC have started to come on, more in the past 2 days. What should I do to fix this? I have changed the alternator and the battery and it still keeps coming on

Hello Al, The throttle sensor is quite a common fault with the Dodge Journey. The throttle body might need to be replaced.

My etc light came on and now the car isn’t starting what do i do? its not even turning its my moms car and she’s on vacation

Is the car turning over? Things to check are battery charge and connectors. Throttle body is often an issue, sometimes to do with the sensor.

Hello, I have a 2014 journey and I get the ETC and the ESC indicators on. Usually I pull over, turn off the car and wait a few seconds but now it’s happening more often. What is this and how can I fix it? Now it barely even starts half the time what is wrong?

Hi Angel, It’s usually to do with the throttle body. Usually throttle control sensor or position sensor, sometimes the wiring. An issue with the throttle may disable the ESC, so sorting out the throttle issue is likely to fix the ESC issue.

Battery died.Had it jumped.Cars great never any problem. We under reaio are buttone to push for Air, a C button, from, rear ans slippery traction. We t g we button next to air that has C on it bliks :& I don’t know ow if could be a fuse of something more serious My husband fixed these problems but he passed suddenly 90 days ago Can someone answer my question please. I’m in Florida and you can’t dive In aug8with no circulating air. I’m at [email protected]

I have a 2011 journey with 131791 miles on it for the 1st time since owning it in the little center window it’s showing what gear I’m in p r d but it also has a round clock like light right next to the gear light what does that mean I have had nothing but problem’s with this piece of junk the Camara quit heated seats quit had to replace a heater core had to replace head gaskets battery altanator brakes every 1 1/2 years in front worse car ever owned some how front drive shaft got bent or something so the whole car,s vibration was so bad you could not drive the thing .

Hi Dean, Sounds to me like you need to get rid of ASAP. I’m afraid I’m not too sure. Looked into it and can’t find any info. All I can think is that it’s symbol of a reminder – maintenance / service? Hopefully someone else will know.

Hi, there. When I was driving my 2014 Dodge Journey on hyw feeling the car was shaking, I could see my arms were shaking, about half hour later sign on the middle screen looks like a double lined Red Cross while a Ding sound, and disappear soon. Then I got out the Hyw, the shaking was disappeared on 50km/h. Anyone know what’s the sign for? Just changed my tires at Costco three month ago.

I have a 2014, when I put it in reverse a over look of the vehicle comes up on the dashboard with a SERVICE light under it and a dinging sound comes on. This has been going on for awhile, the rear camera works fine and has not ever been damaged. Any ideas on if this is a normal thing or is it something more?

My 2012 journey has a small red polite and a exclamation icon red in colour be for it what does it mean can’t find a explanation any were it is on the rite round dash gauge thanks

Hello everyone while reversing today for my dodge Journey 2018, I noticed a sign came up on the reverse showing clean what does that mean

Hi Teddy, Could it be to do with the backup camera or ParkSense sensors that need cleaning? The ParkView camera is located on the rear of the vehicle above the rear license plate and the outer surface and the underside of the rear fascia/bumper require cleaning and kept clear of snow, ice, mud, dirt or other obstruction for the ParkSense sensors.

I have a 2015 diligence journey. Every now & then going downhill I get an ! Mark and a P. Both are in red circles. Mai

Hi Mai, I should have your vehicle braking system serviced. Always best to have anything to do with brake issues checked out right away. It is worth checking under the hood at your brake fluid levels, as this level will fall over time as brake pads wear low. Also keep an eye on brake pads, they require replacing after a while.

The ETC Light and the traction light lit up. What does this mean? Is it because my air tire pressure is low?

Hi Betsy, It’s unlikely to be related to tire pressure, but it’s best to keep tire pressures up to the recommended values as stated on the sticker inside the door jamb. This will improve stability and fuel consumption. The Dodge Journey does have issues with the throttle body, often needing replacement. This fault can trigger reduced engine power mode (limp home mode) and often systems such as traction control can be automatically deactivated as a result.

What is the small red P with a ! Red icon be for it mean on my 2012 dodge journey it is in the rite round dash gauge

Hi Doug, I’m not sure either I’m afraid. All I can think of is a problem with Park (P). If it would be parking brake related, it would be contained in a circle and parenthesis.

In 2014 dodge journey..the inside lights flashed on and off for 2 minutes while dash had a dinging sound..stopped for a minutes started again..lasted 15 minutes til I got home.. what’s this mean??

Hi Alicia, Is it a specific timed flashing or more of a sporadic flickering? There are some issues with Dodge Journey’s with flicker interior lights, or lights staying on which is related to bad wiring / short issues. A wire that controls lighting to the trunk is a common culprit.

Hit a large pothole and now the ads light along with other lights come on. Sometimes the lights will come on when turning on the ignition and other times it does not. I was told that this could be a wheel bearing problem or an ABS shortage anyone have any ideas.

Hi Eugene, Yes, as you say, wheel bearing is a possibility. There’s also a wheel speed sensor located at each wheel, these sensors are prone to damage and that could also be the issue. If you’re noticing any noise from the particular wheel that hit the pothole, humming noise, looseness in the steering, vibrations etc, this may also be a symptom of a damaged wheel bearing.

Hi I have a 2014 dodge journey and my engine light came on and hasn’t gone off I had a service last week and nothing was bought to my attention. We had a -1 degree morning and the car was frozen could this have an impact on this light coming on?

Hi Kelly, Yes the colder weather can impact on your car. Usually though, it’s the cold weather, triggering the engine light that’s making an already underlying problem worse, hence the light. There’s no way of knowing why the engine light is on other than having diagnostics. When the engine light comes on, you’ll typically have a fault code generated and stored. A diagnostic OBD II tool is used to scan for the codes and point you to where the fault is. You should be able to find an auto workshop where you’ll receive a free diagnostics check.

I had a Throttle Replacement a month ago, for my 2014 Dodge Journey with 67,000 miles at the Dealership. No w, a red sailboat light with a chime just came on. What could this mean. Please help, thank you!

Hi Dionne, A sailboat light? It’s not the engine coolant light is it? (see above)

Hi My Dodge Journey stx 2012 model 3,6 shows slippery Warning light, ABS, Brake and constantly feels like its going to cut but doesn’t cut at all. What it might be?

Hi Xolani, I should check your brake fluid level. A common cause for the ABS and slip indicator light to come on is a faulty wheel speed sensor. However, as your brake light is illuminated, you should have any fault codes read with a diagnostic scanner right away.

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Vehicle Manufacturers

• Mercedes-Benz

Vehicle Type

• Commercial Vehicles

Warning Lights

• Dash Warning Lights
• Car Warning Light Colour Meaning
• Privacy Policy

Dodge Journey Dashboard Lights And Meaning

Dodge Journey is a crossover SUV car marketed by FCA’s Dodge Brand (2009) that gives you a potent engine along with Low starting price. Its infotainment system is so trouble-free to operate with more user -friendly technical features.

This car highly appealed to a next-level performance with comfy driving. It comes with an excessive lean body that makes its infrastructure more stylish and upgrades your status. 

Such trendy cars are composed with so many warning indications displayed on the car’s dashboard. It highlights the malfunctioning of the system’s components, security issues, and immediate maintenance whenever needed. It is highly suggested not to neglect these lights as it can risk the safety of the driver.

Look below the warning lights that demonstrate the respective meanings of these indications.This Dodge Journey dashboard warning lights guide also let you to go through the actions that should be implement when these warnings flickers. You can also refers the other models of Dodge on our site like Dodge Charger, Dodge Durango,  Dodge Challenger and Dodge Ram Truck.

Dodge Journey ABS Warning Light

This dashboard symbol activates to indicate a malfunction in the Anti-lock braking System of your vehicle. In this scenario, you can still use your conventional parking brakes without the assistance of ABS. Later you have to inspect your car at Dodge service centre.

Dodge Journey Air Bag Warning Light

If this dashboard light flickers on your dashboard then it indicates a problem in the airbag system and it could not puff out in a crash or a hit. In this case, get serviced your airbag fault from nearby Dodge service centre.

Dodge Journey Battery Charge Warning Light

This warning light gets turn on when the battery is not adequately charged. If this light stays on for a long time, it indicates some malfunction in the charging system. Go and check your vehicle in the service centre.

Dodge Journey Brake Warning Light

This dashboard light gets active when the parking brake is applied or there is a fault in an anti-lock brake system, may be the brake fluid level is getting low in your vehicle. Suppose this light stays on for a longer time than it indicates that parking brakes are disengaged. So, release the parking brakes as earliest. And if this light is still on then go check your vehicle by Dodge service centre.

Dodge Journey Door Open Warning Light

This light gets activated when the Doors of your Dodge journey remain open and not closed properly.

Dodge Journey Electric Power Steering Fault Warning Light

This dashboard light activates when the electric power steering system is detecting a fault in it. If you continue your drive in this warning light, it can create a risk to your safety.

Dodge Journey Electronic Stability Control Active Warning Light

This dashboard light activates on your Dodge Journey Dashboard to indicates that the stability control system is activated in your car, and it is all set to assist you with the road grip and stability.

Dodge Journey Electronic Stability Control Off Warning Light

This warning symbol illuminates on your Dodge Journey dashboard to indicate that the Electronic stability control system is off in your vehicle. Now it will not assist you in controlling your car.

Dodge Journey Electronic Throttle Control Warning Light

This dashboard light gets activate when it indicates a problem in the electronic throttle control system. In this case, completely stop your vehicle and place it in a PARK position. If this light stays on for a long time, then it may reduce your vehicle performance.

Dodge Journey Engine Check Malfunction Indicator Warning Light

This light displayed on the Dodge Journey dashboard to indicates any malfunction in the engine. This light associates with the Automatic Transmission control system and engine monitoring of your vehicle. In this light, we highly advised you to contact dodge service centre.

Dodge Journey Engine Coolant Temperature Warning Light

This warning light activates to alert the driver that the engine of a vehicle is overheating. If this coolant temperature becomes high, then it indicates the chime sound. In this case, a driver should immediately stop the car and turn off the air-conditioning system. Shift your vehicle into the NEUTRAL transmission and idle the vehicle. Immediately switched OFF your system and called for service and maintenance.

Dodge Journey Engine Oil Pressure Light

If this warning light flickers on your Journey dashboard, then it indicates that your engine\'s oil pressure is getting lower. In this situation, please turn off the ignition and stop your vehicle to check its oil level. If the oil level is average, then you should contact to the Dodge service station as earliest.

Dodge Journey Front Fog Indicator Light

This dashboard light gets turn on when front fog lights are activate in your Dodge Journey.

Dodge Journey High Beam Indicator Light

This dashboard light activates when headlights are activated in your vehicle. In this case, push the malfunction lever forward to turn Off the high beams of your Dodge journey. If high beams are still ON, then pull the lever towards your direction to temporarily activate the high beam.

Dodge Journey Low Fuel Warning Light

This warning light indicates when your fuel level reaches 2.7 L, and It stays on until you add some fuel to your vehicle\'s fuel gauge.

Dodge Journey Low Washer Fluid Warning Light

This warning light gets activated when the washer fluid is getting low in your Dodge Journey.

Dodge Journey Park Headlight On Indicator Light

This warning light gets on when the headlights of your Dodge journey are activated.

Dodge Journey Seat Belt Reminder Warning Light

This dashboard light activates whenever the driver or any passenger\'s seat belt remains unbuckled. If this light remains on for a long time and continues to flash, then you should immediately check the seat belts of all the seats of your car.

Dodge Journey Speed Control Fault Warning Light

This dashboard light indicates when the cruise control system is all set to the desired speed.

Dodge Journey Tire Pressure Monitoring System(TPMS) Warning Light

This light activates along with a pop message on the dashboard that your vehicle\'s tire pressure is getting lower than the recommended values. Check all the tires by Dodge Service Station.

Dodge Journey Transmission Temperature Warning Light

This dodge journey dashboard light gets on to alert that the transmission fluid temperature is getting high. In this case, stop your vehicle and engine. Shift to the NEUTRAL position. When this light gets turned OFF, then you will continue driving.

Dodge Journey Turn Signal Indicator Light

This dashboard light gets turn on to alert the driver that your vehicle is driven more than one mile, or we can say 1.6 km with the turn signal on. This light flashes until the left, or right turn signal is activated.

Dodge Journey Vehicle Security Warning Light

This dashboard light activates on your Dodge Journey instrumental cluster when the vehicle security alarm is ringing, and it flashes slowly when the vehicle is disarmed.

Other Models

Fiat Doblo Dashboard Lights And Meaning

Mask Required Sign

Mercedes Benz EQC Dashboard Lights and Meaning

Mitsubishi Eclipse Dashboard Lights And Meaning

Jeep Wrangler Dashboard Lights And Meaning

Renault Arkana Dashboard Lights And Meaning

Suzuki Alto Dashboard Lights And Meaning

Hyundai Venue Tire Pressure

Renault Captur Dashboard Lights And Meaning

Fiat Panda Cross Dashboard Lights And Meaning

© 2023 warningsigns.net

• Fuel Consumption
• Engine Sizes
• Engine Torque
• Engine Power
• Towing Capacity
• Seating Capacity
• Steering Wheel Size
• Dimensions and Weight
• Fuel Tank Sizes
• Trunk Space
• Tire and Rim Sizes
• Bolt Patterns
• Coolers and radiators
• Radiator Fan
• Heat Exchanger
• Intercooler
• Timing Belt
• Sizes of Wiper Blades
• Cabin Filter
• Fuel Filter
• Transmission Fluid
• Antifreeze & Coolant
• Brake Discs
• Brake Drums
• Brake Fluid
• Bulbs For Fog Lights
• Bulbs For Headlights
• Bulbs For Turn Signals
• Bulbs For Licence Plates
• Bulbs For Markers
• Bulbs For Rear Fog Lights
• Bulbs For Backup Lights
• Bulbs For Brake Lights
• Technical Specs
• Car History

• Engine & Fuel
• Coolers and Radiators

Lightning Bolt on Dashboard in Dodge Journey - What’s This?

CarAraC auto mechanics and car experts

Your Dodge Journey has warning lights that illuminate on its dashboard , just like every other modern car. For example; the vehicle security warning, brake warning, airbag warning, battery warning, engine oil pressure warning, etc. Then there's the lightning alert that you may not be familiar with.

Lightning bolt warning lights highlights

• Common reasons: throttle control problems
• How to fix: disconnect the battery for some time, use scanner and get trouble codes
• Possible consequences: you may get stranded
• Priority level: High
• Can you drive? Carefully
• DIY repair: Impossible
• Repair price range: $150-$800

Brief Background to the Dodge Journey

Dodge Journey vehicles are medium-sized crossover SUVs (CUVs) that are issued by the Dodge brand. They were first released in 2009. Then there was a rebadge to the Fiat Freemont in 2011 as a parallel collection. The cars come in right-hand and left-hand drive.

The Dodge Journey comes with warning indicators just like other Dodge models. When these warning lights come up; it could be a system malfunction, security issue, or need for urgent maintenance.

Driver safety shouldn't be taken for granted, especially when a warning light comes on. Taking a related risk could be bad for you and/or the vehicle

What Is the Electronic Throttle Control on a Dodge Journey?

Your Dodge's electronic throttle control features an accelerator pedal module which has a motor, sensors, and a throttle plate. It's a great improvement from the traditional mechanical linkage in old-model cars. Although it isn't immune to mechanical faults.

The ETC measures the pressure drivers apply on the gas/accelerator pedal. The pedal isn't mechanically linked to the engine. A sensor tracks the pedal's position and the data is transmitted to the ETC for engine RPMs (revolutions per minute) to be adjusted.

Gas pedal pressure will determine how much the throttle passage will be opened. There's a flat valve at the opening that's regulated by the pedal's movement. It's called the throttle plate or butterfly valve.

The throttle plate rotates inside the throttle body when you depress the pedal. Then the air will be let into the intake manifold and quickly drawn into it by its vacuum.

1) Sensors in the ETC System

Two sensors that are instrumental to the ETC's operations include the following:

• Mass Airflow (MAF) Sensor

The mass airflow (MAF) sensor calculates the change in airflow. It will then send results to the engine's control unit (ECU) or electronic control module (ECM). This sensor is usually located between the throttle body and the air cleaner.

• Throttle position (TPS) Sensor or Throttle Valve Position Sensor

It's linked to the throttle body and it tracks your Dodge's throttle angle. You can find it on the reverse side of the throttle plate.

Don't get confused about the two sensors mentioned above. The TPS simply informs the ECU/ECM that you've depressed the gas pedal, while the MAF detects the air added. The NAF

2) The Role of the ECU

It's the ECU that controls the balancing of the air-fuel mixture in real-time. It also calculates the best moment to activate the spark plugs to ignite the balanced air-fuel combination.

3) Wide-Open Throttle (WOT)

This is what's referred to as full throttle. It's when the throttle is fully opened on an internal combustion engine or in your car. WOT also means the max-speed state of running an engine or the usual condition of a completely opened butterfly valve or throttle plate.

Your depression of the gas pedal in this situation is referred to as "flooring it". There'll be maximum intake of air because of the lowest resistance to incoming air.

What Does the Electronic Throttle Control Warning Light Mean?

The electronic throttle control warning light on your Dodge Journey could mean that the system has detected a communication problem that has resulted in an ETC error. It's most likely a result of a miscommunication between the ETC and its related sensors.

Dodge Journey vehicles were introduced almost a decade and a half ago, so the dashboard instrument cluster arrangement may vary based on the model year of your car. Still, the lightning symbol is very easy to notice when it illuminates.

Electronic Throttle Control Warning Light Behavior

The electronic throttle control warning light can be a troublesome alert that can come on at any time after the first illumination. And it can go off easily and come on after some days or even weeks. It may stay on for hours in some cases, only to stop when you restart the vehicle.

It will seem like the alert has a mind of its own. Worse still, the symptoms of the fault may not be easy to notice. The car might just be driving just fine regardless of the warning light. There's no need to get confused or nervous.

The ETC light could stay on after the initial indicator check when you first start your car. It could also activate when driving. Even the check engine light (CEL) could activate with it simultaneously.

What To Do Immediately After Noticing the ETC Warning Light

You could continue driving, but it wouldn't be the best move. Just remember to get the car checked at your earliest convenience if you decide to take the RISK.

Drivers could also stop the Dodge instead and park it at a convenient spot or put it in "park". Then proceed to put the engine off and cycle the ignition. The warning light may go off at this point.

Your car should be drivable if the alert doesn't go off. But the vehicle will need to be serviced ASAP. In case of the light flashing, then you should understand that the problem is a severe one that demands more urgency. It won't be advisable to drive the car in such a scenario, but you actually could.

Utilize a diagnostic scan tool to check for vehicle fault codes if you have one. This should be done before any other thing-be it DIY physical checks or hiring a professional technician. It may save you from getting scammed by the dealer or mechanic with a wrong diagnosis and unnecessary repair bills.

Ask the professional or dealer attending to you if they can let you be with them in the vehicle as the diagnoses are taking place. Some repairers offer such a service.

You'll have to take your car to the dealer or auto repair workshop immediately if you don't have a scan tool. Decreased engine power, rough engine noise, or abnormally high idle speed may be experienced if you drive the Dodge while the light is flashing.

Performance issues such as misfiring, stalling, and unstable throttle feedback when the light comes on while driving means you must stop the car. Towing the vehicle to a repairer is recommended at this point if you want to avoid complicating the situation.

Other Symptoms of a Bad ETC

You should look out for the following signs when the ETC alert comes on:

• Idle surges
• Rough idling
• Uninitiated acceleration (car accelerating by itself)
• Reduced fuel mileage (poor fuel economy)
• Engine misfiring

Electronic Throttle Control System Reset Procedure

The problem being indicated by the ETC light might just be the need for a gas pedal reset. The pedal position might not be well lined up or aligned. This will result in a communication error with the sensors that trigger the motor which closes or opens the throttle. Such could be the case in a high-mileage Dodge Journey.

Thankfully, the pedal reset can be done on your own instead of hiring a professional. Follow the steps below carefully to reset the pedal.

• Step 1: Switch on the ignition key without starting the vehicle.
• Step 2: Press the accelerator pedal to the floor and ease it up.
• Step 3: Start the vehicle and depress the pedal again. Observe whether your Dodge will respond or not. Check to see if the ETC light has gone off as well.
• Step 4: Proceed to drive the car around to see if the ETC is working well and if there are no other issues.
• Step 5: Take the car to a repair place if the throttle problem continues and the ETC light is still on.

Most of the warning lights that illuminate on your dashboard can't be taken for granted. And the Dodge Journey electronic throttle control warning light isn't an exception. That's why they're referred to as warnings. Always deal with the lightning symbol alert coming on as soon as possible.

Scanning your Dodge for diagnostic trouble codes (DTCS) will help in eliminating so many possibilities related to the ETC alert. It will save you from diagnostics bills at a repair shop or wasting money on "trial and error". You may only need to do a simple fix such as swapping out the air filter and ETC sensor, or resetting the pedal.

About the authors

The CarAraC research team is composed of seasoned auto mechanics and automotive industry professionals, including individuals with advanced degrees and certifications in their field. Our team members boast prestigious credentials, reflecting their extensive knowledge and skills. These qualifications include: IMI: Institute of the Motor Industry, ASE-Certified Master Automobile Technicians; Coventry University, Graduate of MA in Automotive Journalism; Politecnico di Torino, Italy, MS Automotive Engineering; Ss. Cyril and Methodius University in Skopje, Mechanical University in Skopje; TOC Automotive College; DHA Suffa University, Department of Mechanical Engineering

Add comment

Car Insurance

Home & renters insurance, car repair estimates, read car content, jerry data & research, what does the dodge journey traction control light mean.

Why your Dodge Journey traction control light turns on

Can you drive with the traction control light on, don't get ripped off, temporary loss of traction, faulty wheel speed sensors, anti-lock braking system (abs) malfunction, low tire pressure, broken tcs control module, traction control system turned off.

“I was tired of looking around multiple websites, so I decided to give Jerry a try. Let me tell you—the process is so easy and simple, and they really find you the best prices for your coverage level. Getting insurance for my new car was quick and easy!” —Joanna D.

What Does the Nissan Traction Control Light Mean?

What Does the Dodge Charger Traction Control Light Mean?

What Does the GMC Traction Control Light Mean?

Read advice from car experts at jerry.

2017 Impala Bolt Pattern

How to Prevent Audi A3 Catalytic Converter Theft

2017 Ford Focus Engine Oil Capacity

Browse Questions from Car Experts

Where is the 2003 hyundai sonata obd port location, how do you open an infiniti g37 gas tank.

How long will a DUI stay on my driving record in Louisiana?

Browse More Content

Insurance resources.

• Is Jerry Legitimate?
• Types of Car Insurance
• Car Loan Payment Fluctuations
• Buying a Car With No Credit
• How to Lower Insurance Premiums
• Bad Insurance Decisions
• Why is Car Insurance so Expensive?
• Buying a Used Car
• Adding a Name to a Car Title
• Removing a Name From a Car Title

Insurance for Your Car

• Infiniti M37 Insurance Cost
• Mitsubishi Outlander Insurance Cost
• Ford Transit Insurance Cost
• Lincoln Aviator Insurance Cost

Insurance in Your State

Insurance in your city.

• Broomfield CO Insurance
• Huntington NY Insurance
• Saint Ann MO Insurance
• Bolivar MO Insurance
• Washington PA Insurance

Easiest way to compare and buy car insurance

Car insurance by make, car insurance by model, car insurance by state, car insurance by city, car loan by make, car insurance by company, car loan by state, car repair by service.

• Forum Listing
• Marketplace
• Advanced Search
• Dodge Truck, SUV and Van Forums
• Dodge Ram Truck 3rd Gen (02 – 08) Forums
• 3G Dodge RAM - General Talk

All Warning lights on while driving

• Add to quote

A unique situation occured this week (it was a wet slushy week) While driving my 2008 Ram 4x 4 home at 50- 60 mph after a busy day with it, moving daughters furniture , the dashboard lit up with every warning light, and speedo went dead, and then a few seconds later it would all come back on , engine did not die,truck kept running, it continued to do this randomly about 12 times over the course of the hour drive home. I brought it to dealer next morning, it only did it once while the service tech was writing the milieage down to bring it inot shop, but did not do it for the actual mechanic . The mechanic put on computer readout tool and yes it did show that truck "lost communication" a dozen times that day and the one more time that day. But they were unable to pinpoint the problem. No fault codes other than "lost communication". They gave it back to me and suggested we see if it clears it self up or wait till it does it again (and do what ?) they only charged me 65 bucks because they felt bad could not find. Anyway, this truck has 80,000 km (so 50,000 miles) I have made no electrical changes to it, no other problems. It is a cold and wet environment up here so maybe a bad connector that has dried it self out since then . It has not done the warning lights again today when I drove it. Any ideas or similar problem that you got fixed ????  

Just a haunch but check the ground wire from the battery to the chassis. Make sure all the wires are tight to the terminal and that the terminals are clean.  

I second that.. The ground is most important..  

Fred had that problem it would come and go intermittenly. Turned out to be the fuse box. He repalaced it. You can check the connector's under it to make sure there clean and tight. Maybe try grabbing the wire connector underneath and wiggling it to see if the problem show's up.  

Lost communication with what module? The code always tells you what module it lost communication with. If all the lost communication codes say cluster then you probably have a cluster going out on you. Tell the dealer to run a Loss of Comm. test through wiTech. If they don't know what you are talking about then go to another dealer.  

thanks guys, I would assume dealer mechanic would of checked ground from battery, but I will double check and alos wiggle the fuse box to see if I can make it happe. I had the trucl oilsprayed in November 2012 , maybe it got into somewhere it shouldn't of. Also will suggest to dealer to do the witech thing if it does it again.  

Well update it has only got worse but more random. I took apart all the battery connections and cleaned and the ground to the body fender and large connection on outside of fuse box. reset computer , tested gauges using that method of holding odometer reset while turning key to on, and all supposedly okay. But still randomly while driving all warning light and chimes come on and guages die and then a few seconds later back to normal and does this a dozen times while driving in to work. then next day will not do it at all , same road same bumps , same temp. Dealer only sees advantage to see it if it is doing it while they are looking at it. Of course it is never doing it when I drive by the dealer !!! I checked all the plugs under the seats too. I am ready to trade this in and look at buying a pre 1980 vehicle without all these computer aspects to go wrong !!  

TIPM!! had the sam situation, all warning lights on and off.....turned out I needed to have the TIPM replaced....only cost about $700 CDN Oh and I have a 2008 5.7 1500 4x4.  

I knw this is off topic but i have been looking at other posts about the foglight bypass for being able to keep you foglights on while you are running with your highbeams. But does anybody know how to do this on a 2006 ram 4.7 Can anybody help me with this??? \  

Hosey........maybe dumb question but what does TIPM stand for and tell me more about how your dealer figured out it was that ? please and thanks  

Yup, Total Integrated Power Module. I never heard of such a thing till about 2 months ago. I was driving down the road (it was the first snowfall of the season). I went 5 mins down the road and got to the hardware store and parked. Then bam....all lights on the dash, warning bells.....I sat for a minute and did the whole WTF. turned the truck off and then back on and nothing....as if nothing happened. The roads were wet and sloppy snow slush crap. A few days later was in the truck, flipped it into 4x4 and then BAM....lights, warnings, and then the truck died! nothing.....it would even turn over....I finally got it to turn over, and dropped it off at the dealership (it was the nearest shop, only reason). They plug it in and tell me the TIPM died. Im not a mechanic but the issues that i was having woth the truck were all electrical and speratic.... This might not be your issue with your truck but the thread title "warning lights" caught my eye. good luck bro.  

The TIPM's replaced most of the fusebox. Personally, I don't like it. On paper it's cheaper for manufacturing, simpler to check and replace, cleaner under the hood, and when it fails, it gives Dodge and the dealership a much bigger payday under your hood. :imo  

• ?            
• 291.4K members

Top Contributors this Month

Dodge Journey Brake Warning Light: Meaning, Causes, + How to Fix

Your Dodge Journey ‘s brake light indicator is there to inform you of an issue with your vehicle’s brake system. It is a light different from the anti-lock brake system, which has its own ABS warning light . 

The brake light indicates a problem with the physical braking system itself.

Check the Emergency Brake First

If you read this article trying to figure out whether to drive your vehicle, check the emergency brake first. 

If it’s engaged, the brake light will stay lit. If the handle isn’t all of the way down, it’ll cause the brake warning light to stay on. Check to make sure that there isn’t a little bit left that it needs to turn the brake light off.

Now if the emergency brake didn’t fix the situation, it’s time to look into what is causing your Journey’s brake warning light to stay on. The brake light is perhaps the most critical warning light of all.

We do not recommend driving with this light on at all . Doing so may lead to injury when the brakes fail.

Dodge Journey Brake Warning Light Causes

The brake warning light indicates that your Journey has detected that one of its major brake components has failed, typically seen through a pressure loss. 

You’ll feel a loss of pressure that manifests itself in the form of a “mushy” brake pedal (low brake fluid level).

If the brake light is only coming on when you push the brakes, that’s a definite indication that the pressure in the brake system is too low. Either the brakes need to be bled, or there is a leak.

Brake Fluid Leak

Since you’ve already checked the emergency brake handle, now it’s time to check the master cylinder and see if the brake fluid is low or not. Now if it is low but not empty, adding more may provide a temporary fix.

If the brake fluid looks like it is out, you’ll need to add more, bleed the brakes, and ideally fix the problem so that you aren’t repeating all of this again. If the brake fluid leaks over the brake pads and shoes, it means poor brake performance.

Just remember, it had to leak out somewhere, and adding fluid without fixing the problem is a temporary solution. The leak can get worse over time and lead to brake failure.  Look around the brake calipers and brake lines for the leak. Look for fluid under your Journey, where you usually park.

Pressure Differential Switch

Your brake system is divided into two circuits. These circuits cut the brake system in two. That way, if the brake system gets a leak or fails, you still have brakes on half of your Journey’s wheels.

The pressure differential switch measures the difference in pressure between the two circuits and will report that there is a difference by turning on your Journey’s brake warning light.

In most vehicles, this switch is located in the master cylinder . You’ll see a harness plugged in somewhere around there.

Worn Brake Pads

Worn brake pads are often a cause of the brake warning light coming on. The pads have built-in wear sensors that will trigger the light whenever they get down to a certain thickness.  These sensors are known as squealers, and you’ll hear.

This is important because it alerts you to replace your brakes before they become too thin and can’t stop the vehicle properly. If your brakes are worn, be sure to have them replaced as

Check the Brake Lights

Some vehicles will now activate the brake warning light on the dash if the actual brake lights behind it have failed. Check to see that both of them are lighting up. If not, try replacing the bulb and see if that solves the problem.

How to Turn off Your Journey’s Brake System Warning Light

The only way to turn the brake light off is to restore proper line pressure to both brake circuits when the pedal is pushed.

Don’t drive if your Journey is having trouble stopping or noticeably leaking fluid. Have it towed to a mechanic.

If you mess up fixing your engine, the vehicle does not move. If you mess up fixing the brakes, it doesn’t stop. That’s infinitely more dangerous.

If your Dodge Journey’s brake warning light is on, and you’ve checked the emergency brake, you’ll need to look for a leak in the lines, calipers, wheel cylinders, master cylinder, etc. Good luck diagnosing the issue. If there is anything that you would like to add, please leave a comment below.

• Lights & Lighting Accessories
• Lighting Assemblies & Accessories
• Brake & Tail Light Assemblies, Parts & Accessories
• Tail Light Assemblies

Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime Try Prime and start saving today with fast, free delivery

Amazon Prime includes:

Fast, FREE Delivery is available to Prime members. To join, select "Try Amazon Prime and start saving today with Fast, FREE Delivery" below the Add to Cart button.

• Cardmembers earn 5% Back at Amazon.com with a Prime Credit Card.
• Unlimited Free Two-Day Delivery
• Streaming of thousands of movies and TV shows with limited ads on Prime Video.
• A Kindle book to borrow for free each month - with no due dates
• Listen to over 2 million songs and hundreds of playlists
• Unlimited photo storage with anywhere access

Important:  Your credit card will NOT be charged when you start your free trial or if you cancel during the trial period. If you're happy with Amazon Prime, do nothing. At the end of the free trial, your membership will automatically upgrade to a monthly membership.

Return this item for free

Free returns are available for the shipping address you chose. You can return the item for any reason in new and unused condition: no shipping charges

• Go to your orders and start the return
• Select the return method

This item has been tested to certify it can ship safely in its original box or bag to avoid unnecessary packaging. Since 2015, we have reduced the weight of outbound packaging per shipment by 41% on average, that’s over 2 million tons of packaging material.

Image Unavailable

• To view this video download Flash Player

MZORANGE LED Inner Tail Light Lamp Stop Brake Indicator Warning Light For Dodge Journey 2012 2013 2014 2015 2016 2017 2018 with Bulb (Right Passenger Side)

Purchase options and add-ons, about this item.

• 🚗Fit For Dodge Journey 2012 2013 2014 2015 2016 2017 2018
• 🚗Meets or exceeds DOT/SAE standards, with particular consideration for photo metric and safety compliance.Waterproof and shock resistant. no modification necessary, plug and play, install is easy.Meets or exceeds DOT/SAE standards, with particular consideration for photo metric and safety compliance.Waterproof and shock resistant. no modificatio necessary, plug and play, install is easy.
• 🚗Special coating on the lens surface prevents hazing and fading, ensuring proper illumination and operational safety.Rigorous and accelerated cycling tests to ensure product service quality and durability.
• 🚗Package Included: 1 PC Tail Light (Right Passenger Side)
• 📧Each Of Our Products Is Elaborately Designed And Manufactured,We Have A Strict Quality Control System To Ensure A Stable Quality. If you have any questions, please feel free to contact us, we will get back to you within 24 hours.

Buy it with

Similar items that may deliver to you quickly

From the brand

Our was established in 2019, is a professional supplier engaged in the research, development, sale of car accessories.

In recent years, our company has introduced a series of products. The products are designed, manufactured, tested by our R&D team and passed variousCertification.

Whether selecting a current product from our catalog or seeking professional assistance for your application, you can talk to our about your sourcing requirements.

MZORANGE Tail Light Lamp

Product Description

About tail light.

• If you are looking for exquisite and outstanding For Dodge Journey tail light, then this set of excellent For Dodge Journey warning light is your ideal choice.

Detailed introduction

• For Dodge Journey 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018
• Durable ABS plastic body,meets or exceeds DOT/SAE standards.
• Please make sure this item fits for your vehicle before you purchase.
• OMG:4806369AF, 4806368AF
• For easy install
• Light bulb is included

• Before you begin installation, please inspect the tail light of damage. Do not install them if there is any damage.
• Please make sure that the tail light are firmly installed before driving.

Product information

Technical details, additional information, warranty & support, compare with similar items, looking for specific info, customer reviews.

Customer Reviews, including Product Star Ratings help customers to learn more about the product and decide whether it is the right product for them.

To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzed reviews to verify trustworthiness.

Reviews with images

• Sort reviews by Top reviews Most recent Top reviews

Top reviews from the United States

There was a problem filtering reviews right now. please try again later..

Top reviews from other countries

• Amazon Newsletter
• About Amazon
• Accessibility
• Sustainability
• Press Center
• Investor Relations
• Amazon Devices
• Amazon Science
• Sell on Amazon
• Sell apps on Amazon
• Supply to Amazon
• Protect & Build Your Brand
• Become an Affiliate
• Become a Delivery Driver
• Start a Package Delivery Business
• Advertise Your Products
• Self-Publish with Us
• Become an Amazon Hub Partner
• › See More Ways to Make Money
• Amazon Visa
• Amazon Store Card
• Amazon Secured Card
• Amazon Business Card
• Shop with Points
• Credit Card Marketplace
• Reload Your Balance
• Amazon Currency Converter
• Your Account
• Your Orders
• Shipping Rates & Policies
• Amazon Prime
• Returns & Replacements
• Manage Your Content and Devices
• Recalls and Product Safety Alerts
• Conditions of Use
• Privacy Notice
• Consumer Health Data Privacy Disclosure
• Your Ads Privacy Choices

Dodge RAM Warning Light Symbols and Meaning (FULL list, FREE Download)

If you’ve ever been surprised by an unexpected warning light on your Dodge RAM dashboard, you’re not alone!

I’m here to help!

In this guide, you’ll get comprehensive information about Dodge RAM warning light symbols with a full list of Dodge RAM dashboard lights and meanings in an image and an E-book (FREE Download).

Let’s take a look at my list!

Dodge RAM Warning Lights/Indicators and Meanings

Click the symbols for details if you want.

Electronic Throttle Control Warning Light

This warning light will illuminate to indicate a problem with the ETC system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.

Air Bag Warning Light

This warning light will illuminate to indicate a fault with the airbag and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position. This light will illuminate with a single chime when a fault with the airbag has been detected, it will stay on until the fault is cleared. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.

Vehicle Security Warning Light

This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.

Battery Charge Warning Light

This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible. This indicates a possible problem with the electrical system or a related component.

Seat Belt Reminder Warning Light

This warning light indicates when the driver or passenger seat belt is unbuckled. When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.

Brake Warning Light

This warning light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.

Engine Coolant Temperature Warning Light

This warning light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound. If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool, whichever comes first. If the light turns on while driving, safely pull over and stop the vehicle. If the Air Conditioning (A/C) system is on, turn it off. Also, shift the transmission into NEUTRAL (N) and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.

Oil Pressure Warning Light

This warning light will illuminate to indicate low engine oil pressure. If the light turns on while driving, stop the vehicle, shut off the engine as soon as possible, and contact an authorized dealer. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.

Hood Open Warning Light

This warning light will illuminate when the hood is ajar/open and not fully closed.

Liftgate Open Warning Light

This warning light will illuminate when the liftgate is open.

Transmission Temperature Warning Light

This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into PARK (P) and run the engine at idle or slightly higher until the light turns off.

Oil Temperature Warning Light

This warning light will illuminate to indicate the engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Wait for oil temperature to return to normal levels.

Electric Power Steering Fault Warning Light

This warning light will turn on when there’s a fault with the EPS system

Trailer Brake Disconnected Warning Light

This warning light will illuminate when the Trailer Brake has been disconnected.

Door Open Warning Light

This indicator will illuminate when a door is ajar/open and not fully closed.

Engine Check Light

This warning light will illuminate when the ignition is in the ON/RUN position before the engine start. If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after the engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.

Electronic Stability Control Active Warning Light

This warning light will indicate when the ESC system is Active. The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated. It should go out with the engine running. If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected. ● The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position. ● The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive. ● This light will come on when the vehicle is in an ESC event.

Air Suspension Alternate Trailer Height

This light will illuminate when the air suspension system is set to the Alternate Trailer Height setting.

ESP BAS Light

This light indicates a problem with your car’s brake assist program or electronic stability system.

Electronic Park Brake Warning Light

This warning light will illuminate to indicate the Electronic Park Brake is not functioning properly and service is required. Contact an authorized dealer.

4WD High Indicator Light

This light alerts the driver that the vehicle is in the 4WD High mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.

Wait To Start Light

This indicator light will illuminate for approximately two seconds when the ignition is turned to the RUN position. Its duration may be longer based on colder operating conditions. Vehicle will not initiate start until telltale is no longer displayed.

Low Coolant Level Warning Light

This telltale will turn on to indicate the vehicle coolant level is low.

Loose Fuel Filler Cap Warning Light

This warning light will illuminate when the fuel filler cap is loose. Properly close the filler cap to disengage the light. If the light does not turn off, please see an authorized dealer.

Cold Ambient Derate Mode Indicator

This indicator light will illuminate when a derate (engine power reduction) is activated for protection of the turbocharger in cold ambient temperatures.

Electronic Stability Control OFF Warning Light

This warning light indicates the ESC is off. Each time the ignition is turned to ON/RUN or ACC/ON/RUN, the ESC system will be on, even if it was turned off previously.

Service LaneSense Warning Light

This warning light will illuminate when the LaneSense system is not operating and requires service. Please contact an authorized dealer.

Low Washer Fluid Warning Light

This warning light will illuminate when the windshield washer fluid is low.

Service Forward Collision Warning Light

This warning light will illuminate to indicate a fault in the FCW System. Contact an authorized dealer for service

Forward Collision Warning OFF Indicator

This indicator light illuminates to indicate that Forward Collision Warning is off.

Service Stop/Start System Warning Light

This warning light will illuminate when the Stop/Start system is not functioning properly and service is required. Contact an authorized dealer for service.

Tire Pressure Monitoring System Light

The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed. Should one or more tires be in the condition mentioned above, the display will show the indications corresponding to each tire. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life and may affect the vehicle’s handling and stopping ability.

Anti-Lock Brake System Light

This warning light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on. If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.

Rear Axle Locker Fault Indicator Light

This warning light will illuminate to indicate when a rear axle locker fault has been detected.

4WD Indicator Light

This light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.

Water In Fuel Indicator Light

The “Water In Fuel Indicator Light” will illuminate when there is water detected in the fuel filter. If this light remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.

Sway Bar Indicator Light

This indicator light will illuminate when the front sway bar is disconnected.

Service Adaptive Cruise Control Warning Light

This light will turn on when the Adaptive Cruise Control (ACC) is not operating and needs service.

Air Suspension Fault Warning Light

This light will illuminate when a fault is detected with the air suspension system.

Low Fuel Warning Light

When the fuel level is less than a ¼ tank, and the Distance to Empty is less than 50 miles, this light will turn on and remain on until fuel is added. A single warning chime will sound with Low Fuel Warning.

Speed Control Fault Warning Light

This warning light will illuminate to indicate the Speed Control System is not functioning properly and service is required. Contact an authorized dealer.

Trailer Merge Assist Indicator Light

This indicator light will illuminate to indicate when Trailer Merge Assist has been activated.

TOW/HAUL Indicator Light

This indicator light will illuminate when TOW/HAUL mode is selected.

Cargo Light

This indicator light will illuminate when the cargo light is activated by pushing the cargo light button on the headlight switch.

Front And Rear Axle Lock Indicator Light

This light indicates when the front, rear, or both axles have been locked. The telltale will display the lock icon on the front and rear axles to indicate the current lock status.

Rear Axle Lock Indicator Light

This light indicates when the rear axle lock has been activated.

Service 4WD Warning Light

This warning light will illuminate to signal a fault with the 4WD system. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest service center and have the vehicle serviced immediately.

4WD Low Indicator Light

This light alerts the driver that the vehicle is in the 4WD Low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels.

NEUTRAL Indicator Light

This light alerts the driver that the 4WD power transfer case is in the NEUTRAL mode and the front and rear driveshafts are disengaged from the powertrain.

Low Diesel Exhaust Fluid Indicator

The indicator will illuminate if the Diesel Exhaust Fluid (DEF) level is low.

Diesel Exhaust Brake Indicator Light

This indicator light will illuminate when the Diesel Exhaust Brake has been activated, and is in full strength mode.

Sway Bar Fault Warning Light

This light will illuminate when there is a fault in the sway bar disconnect system.

Snowplow Mode Indicator Light

This indicator light will illuminate when Snowplow Mode has been activated.

Air Suspension Payload Protection Light

This indicator light will illuminate to indicate that the maximum payload may have been exceeded or load leveling cannot be achieved at its current ride height. Protection Mode will automatically be selected to “protect” the air suspension system, air suspension adjustment is limited due to payload.

Air Suspension Bed Lowering Mode

This light will illuminate when the Bed Lowering Mode procedure is complete.

Air Suspension Ride Height Raising

This light will blink and alert the driver that the vehicle is changing to a higher ride height.

Air Suspension Ride Height Lowering

This light will blink and alert the driver that the vehicle is changing to a lower ride height.

Adaptive Cruise Control Light

This light will turn on when the ACC is SET and there is no target vehicle detected.

LaneSense Indicator Light

The LaneSense indicator light illuminates solid green when both lane markings have been detected and the system is “armed” and ready to provide visual and torque warnings if an unintentional lane departure occurs.

This will display when the ACC is set and a target vehicle is detected.

ECO Mode Indicator Light

This light will turn on when ECO Mode is active.

Park/Headlight On Indicator Light

This indicator light will illuminate when the park lights or headlights are turned on.

Front Fog Indicator Light

This indicator light will illuminate when the front fog lights are on.

Turn Signal Indicator Lights

When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right).

Speed Control SET Indicator Light

This light will turn on when the speed control is set.

Stop/Start Active Indicator Light

This indicator light will illuminate when the Stop/Start function is in “Autostop” mode.

4WD AUTO Indicator Light

This light alerts the driver that the vehicle is in the four-wheel drive auto mode, and the front axle is engaged, but the vehicle’s power is sent to the rear wheels. Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.

Automatic Diesel Exhaust Brake Light

This indicator light will illuminate when the Diesel Exhaust Brake has been activated, and has switched to Automatic mode.

Cruise Control Ready Indicator

This indicator light will illuminate when the cruise control is ready, but not set.

Adaptive Cruise Control Ready Light

This light will illuminate when the vehicle equipped with ACC has been turned on but not set.

Cruise Control SET Indicator Light

This light will turn on when the cruise control is set.

Hill Descent Control Light

This indicator shows when the HDC feature is turned on. The lamp will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the “4WD LOW” position and the vehicle speed is less than 20 mph (32 km/h). If these conditions are not met while attempting to use the HDC feature, the HDC indicator light will flash on/off.

When the LaneSense system is ON, but not armed, the LaneSense indicator light illuminates solid white. This occurs when only left, right, or neither lane line has been detected. If a single lane line is detected, the system is ready to provide only visual warnings if an unintentional lane departure occurs on the detected lane line.

High Beam Indicator Light

This indicator light will illuminate to indicate that the high-beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on, “flash to pass” scenario.

Now you know what your car is trying to tell you and have a better understanding of Dodge RAM dashboard lights.

But it can be challenging to remember exactly the name and meaning of each symbol, right?

No problem!

I’ve compiled the full list of Dodge RAM warning lights and indicators with their meanings in an image and a PDF E-book for you. 

Don’t hesitate to download them for later use!

DODGE RAM WARNING LIGHTS AND INDICATORS

Get access to my full list of these dashboard lights and become a better driver.

What’s Next?

To maintain the performance and safety of your Dodge RAM vehicle, pay attention to any warning lights that may appear on your dashboard.

Remember, when the red or yellow symbols light up, take your car to a mechanic, or buy a scan tool to self-check.

Don’t miss my review on Best Chrysler/Jeep/RAM Scan Tools to find the right tool for you.

FOXWELL NT510

Worried about your Mini Cooper? Check out my complete guide to Mini Cooper Warning Lights .

Share this article

Related Posts

Restraint system warning lamp, seat belt warning lamp, 1 thought on “dodge ram warning light symbols and meaning (full list, free download)”.

Leave a Comment Cancel Reply

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

Recommended for you

Volvo Dashboard Symbols and Meanings

Kenworth Dashboard Lights and Meanings

Freightliner Warning Lights and Meanings

Start typing and press enter to search.

Home » Troubleshooting » Dodge Journey battery light is on – causes and how to reset

Dodge Journey battery light is on – causes and how to reset

When the red battery light comes on in the dashboard of Dodge Journey, it indicates a malfunction in the charging system. This can happen due to a number of reasons which we will discuss in this article.

The most common reason for battery light illuminating in Dodge Journey is faulty alternator. But the battery light can also come on due to a damaged wire, corrosion on electrical connectors, corrosion on battery terminals, bad ground connection and slipping serpentine belt.

1. Faulty Alternator

Alternators can fail at any time, but generally they last over 100,000 miles. Before replacing the alternator, you must rule out other causes that may stop or degrade flow of current from the alternator, for example: bad electrical connection or damaged wire.

How to test the alternator

The easiest method to check the alternator is by measuring the voltage at the battery terminals when the engine is running.

• Start your Journey.
• Connect the black cable of the multimeter to negative terminal of the battery, and the red cable to the positive terminal.
• The voltage should be between 13.5 and 14.8 volts with the engine running.
• Switch on the accessories in your Journey, for example, headlights, AC fan at full speed, and interior lights.
• The voltage should remain around 14 volts. If it drops and remain below 13.5 volts, it indicates a problem with the current supply from the alternator.
• If the voltage drops below 12 volts with the engine running and the accessories turned on, it means the current supply from the alternator is completely cut off and all the electronics are solely powered by the battery.

Can you drive Journey with a bad alternator?

Yes, you can drive your Journey with a bad alternator, but only for a short distance. The battery charge will go down as you drive since all the on-board electronic controllers and accessories are now solely powered by the battery. When the battery charge gets too low the engine will shut down, and you will be stranded.

Recommended video

2. Poor ground connection

What is a ground connection.

The negative terminal of the battery is connected to the body/chassis of Journey, called a ground connection. The engine also requires a ground connection to function, but the way the engine is mounted, it does not allow the electric current to flow between the engine and the body (due to non-conductive rubber insulated engine mounts). For this purpose, a ground strap/wire is used to connect the engine and the chassis.

What happens when the ground connection goes bad?

If the ground connection of the chassis or the engine goes bad in your Journey due to rust or corrosion, you will face all sorts of electrical issues, including battery light illuminating in the dashboard. The alternator relies on the ground connection of the engine to function properly. When the ground is bad, the current supply from the alternator will be reduced or may fluctuate. Additionally, in rare cases the contact between the engine block and the alternator can also go bad due to corrosion.

How to check if the ground connection is good?

You can check the quality of the ground connection in Journey by doing a conductivity test between the negative terminal of the battery and the engine. Take a multimeter, change its settings to ohms symbol. Touch one probe to the negative terminal of the battery, and the other probe to any exposed metal part of the engine. The reading should be at or very close to zero ohms. Do the same between the negative terminal of the battery and exposed metal part of the alternator.

Inspect and clean the ground connections

If the conductivity test fails, check the condition of the ground connections in your Journey. Inspect the connectors of the ground cables (battery to body, body to engine) for any signs of rust or corrosion. Clean the contacts with a sandpaper or wire brush. You may also have to remove the alternator and clean the ground contact area on the alternator and on the engine block.

3. Poor battery connection

It is possible the alternator in your Dodge Journey is working properly, but the current flow is interrupted due to a loose electrical connection, a damaged wire, or corrosion on the battery terminals.

Corrosion on battery terminals

Battery corrosion is a fairy common problem (except in AGM batteries), especially if the installed battery is more than 2 years old. Corrosion occurs when the battery acid reacts with the metal terminals which can lead to loss of contact and reduced current flow. If there isn’t enough current flow, the battery will not be charged properly, and may cause engine starting problems.

Check battery terminals

To know if your Journey charging system problems are from dirty battery terminals, you need to investigate them. Lift the plastic covers over the terminals and check for any signs of corrosion. If you discover white deposits or silvery-green deposits, but no further cracks or damage, you may not have to replace the battery or the alternator, just clean the battery terminals.

Clean the battery terminals

Quick cleaning: There is a neat little trick with which you can clean corrosion on the battery terminals of your Journey in under a minute. Pour hot boiling water over the corroded terminals and the corrosion will just melt away. Do one terminal at a time and don’t let water puddle on the top of the battery touch both terminals at the same time, this can short the battery.

Thorough cleaning: To thoroughly clean the battery in your Dodge Journey, you have to remove the terminal cables first, which requires no special knowledge, just a little concentration, as the order is very important. First remove the black cable from the negative terminal using a wrench or a plier. Next you can unplug the red positive terminal cable. Be careful not to touch both terminals with your metal tool, it will be one expensive mistake. Once the battery has been removed from the circuit, you can start cleaning the corroded battery with sandpaper or wire brush. After cleaning, reconnect the cables in reverse order, positive first, then negative.

4. Slipping serpentine belt

The serpentine belt, also known as accessory belt or drive belt, transfers the power from the engine to other components like the alternator and the AC compressor, that are essential for normal operation of your Dodge Journey.

If the serpentine belt is damaged or becomes loose, or if the alternator pulley develops a defect, it can cause the belt to slip. This can cause the alternator to spin slower or inconsistently and the electricity production is degraded. When the on-board diagnostic system detects low voltage from the alternator, the battery symbol light comes on in the instrument cluster of Journey.

Symptoms of bad serpentine belt

The most common sign of bad serpentine belt in Journey is squealing noise from the engine compartment. Another prominent sign is visible cracks on the ribbed part of the belt. A slipping accessory belt can also cause burning smell.

Sound of a slipping serpentine belt

If the serpentine belt is found to be defective, it must be replaced. Keep in mind that a slipping belt is not always defective, it can slip due to a number of reasons, including due to a bad tensioner pulley or any other pulley.

5. Rodent damage

If rodents like rats, mice, or squirrels have chewed up the cables for the alternator, it can cause the battery light to turn on in Journey. Look for any signs of bite marks in the engine compartment, and examine all the cables for the alternator. If any cable has been damaged, replace it with a new one.

How to reset the battery light

Fix the issue.

Resetting the battery light in Journey without solving the underlying issue may not help, as the warning light will turn back on when the system again detects the fault. The light should disappear automatically after fixing the issue. If it doesn’t turn off immediately, driving your vehicle for a few miles should help.

OBDII scanner method

The proper way to reset the battery light in Journey is by clearing the codes with an OBDII scanner. If the warning light doesn’t turn off automatically after fixing the issue, you will have to do it manually by connecting a diagnostic device and then deleting all the error codes related to the charging system.

Disconnect the battery

If you don’t have a diagnostic device, it may be possible to reset the battery light in Journey by disconnecting the battery for a few minutes. Remove the cable from the negative terminal of the battery first, then from the positive terminal. With the battery disconnected, press the horn button a few times and turn on the headlights to drain out all the residual electricity from the system. After about 15 minutes, reconnect the battery in reverse order: positive cable first, then negative cable.

Use OBD2 scanner for diagnosis

Since Dodge Journey is equipped with on-board diagnostics (OBD), a fault diagnosis can provide initial indications of where the malfunction is located.

To begin troubleshooting, you must first connect the diagnostic tool to your Journey. The OBDII connector is usually located under the dashboard. With the tool connected, turn on the ignition. Most diagnostic devices then ask for some information about the vehicle. It is important that you enter this 100% correctly, otherwise the result of the search may be inaccurate. In addition to the vehicle make, model, and engine type, you usually also have to type in the Vehicle Identification Number (VIN). Since some OBD codes are manufacturer-specific, the scanner will be able to give you more accurate information if you enter more details about your Journey.

When the battery light comes on in your Dodge Journey, you should always start with testing the voltage at the battery when the engine is running. If the voltage test fails, then move on to testing the alternator and its electrical connections.

In any case, it is advisable for laypersons to visit a workshop. A professional mechanic can swiftly diagnose the charging system issue for you.

• Kia Sedona auto windows not working, how to reset
• Jaguar E-PACE low oil pressure light is on – causes and how to reset
• Ford S-Max steering wheel vibration causes and diagnosis
• Mitsubishi Delica bad alternator symptoms, how to check voltage
• Chrysler Sebring makes sloshing water sound – causes and how to fix it
• Cadillac DeVille dashboard lights flicker and won’t start – causes and how to fix it
• Buick Terraza auto windows not working, how to reset
• Infiniti QX80 AC smells bad – causes and diagnosis
• BMW X6 low oil pressure light is on – causes and how to reset
• SEAT Toledo Apple CarPlay not working – causes and how to fix it
• Toyota 86 key fob won’t lock or unlock the doors
• Jaguar XF makes sloshing water sound – causes and how to fix it
• Chevy TrailBlazer makes grinding noise when starting – common causes
• Adjusting Blind Spot Alert settings in Jeep Grand Cherokee
• Android Auto on Audi SQ2, how to connect
• Maserati Levante Android Auto not working – causes and how to fix it
• Android Auto not working – causes and how to fix it
• Toyota Verso bad spark plugs symptoms, causes, and diagnosis
• Fiat Panda uneven tire wear causes
• Jaguar E-PACE dead battery symptoms, causes, and how to jump start

Dodge Electronic Throttle Control Warning Light

Have you ever had that “Uh-oh” moment where you realize your car is speeding, but you can’t seem to get the speed down? That’s probably because your electronic throttle control warning light is on. In this blog post, we will explore what this light means and how to fix it if it’s flashing. From diagnosis tips to DIY repairs, read on to learn everything you need to know about the Dodge Electronic Throttle Control Warning Light.

What is the Dodge Electronic Throttle Control Warning Light?

The Dodge Electronic Throttle Control Warning Light may indicate a problem with the electronic throttle control system. Some common causes of the light turning on include a bad throttle cable, broken or defective electric motor, and dirty air filters. In order to determine if the warning light is on, you will need to take your car in for an inspection. If the problem is not fixed, the light may continue to turn on even after the issue has been resolved.

How to Fix the Dodge Electronic Throttle Control Warning Light

If you are experiencing a "Dodge Electronic Throttle Control Warning Light" on your dashboard, there is likely a fix available. This warning light typically displays when the vehicle's electronic throttle control system (ETCS) isn't functioning properly and may limit the driver's ability to operate the vehicle safely. In most cases, fixing the ETCS can resolve the warning light. Here are four common causes and solutions for the Dodge Electronic Throttle Control Warning Light:

• The module that controls ETCS may be faulty. In this case, it may be necessary to replace the module.
• The wiring may be incorrect or damaged. If this is the case, it may be necessary to replace the wiring or reconnect it properly.
• The computer that controls ETCS may be overloaded or overworked. If this is the case, it may be necessary to clean or update the computer.
• There may be a problem with one of the sensors in ETCS. If this is the case, it may be necessary to replace one of the sensors.

What to do if the Dodge Electronic Throttle Control Warning Light stays on

If the Electronic Throttle Control (ETC) Warning Light stays on, it means that there is a problem with your vehicle's throttle system. You should take your vehicle to a qualified mechanic or dealership for diagnosis and repair.

If you're experiencing an issue with your Dodge Electronic Throttle Control warning light, don't panic. There are several possible causes and solutions, so read on to find out more. In the meantime, if you experience any issues that might be related to the warning light, take your car in for service as soon as possible.

What does it mean if the electronic throttle control light comes on?

There are a few potential reasons why the electronic throttle control (ETC) light would come on. One possibility is that there is an issue with the throttle position sensor (TPS), which is used to determine how far the throttle plate should open based on input from the gas pedal. Another possibility is that there is a problem with the ETC itself. If the light comes on and flashes, it means there is definitely a problem with either the TPS or ETC, and the vehicle should be taken to a mechanic for diagnosis and repair.

How do I fix my electronic throttle control light?

The electronic throttle control light is an indication that there is a problem with the throttle body or related components. In most cases, the best way to fix this problem is to take the vehicle to a qualified mechanic or dealership for diagnosis and repair.

How do I reset my electronic throttle control Dodge?

If your electronic throttle control is acting up, you can try resetting it. To do this, disconnect the battery and then reconnect it after a few minutes. You may also need to remove the fuse for the electronic throttle control before reconnecting the battery.

How much does it cost to fix the electronic throttle control?

It can cost anywhere from $200 to $600 to fix an electronic throttle control, depending on the severity of the problem and which parts need to be replaced.

Was this page helpful?

More important content about Dodge

Code P1693 on Dodge Cummins: Turbo Charge Control Circuit Malfunction

Dodge dakota years to avoid, warning lights in dodge caravan, dodge charger years to avoid - 6 worst years, dodge avenger dashboard warning lights and symbols.

I recently had an issue with the Dodge Electronic Throttle Control Warning Light coming on, and I was really worried. Luckily, I found this blog post which provided a detailed explanation of how to fix the problem in a few simple steps. Following their advice, I was able to quickly resolve the issue without any hassle. It's great to know that there are resources like this out there that can help me if my car ever has issues again!

I recently had to have a S.M., California 2007 Dodge R/T dealer to diagnose an erratic warning light and they indicated that my Throttle pedal control assembly had to be replaced to correct the warning light problem. Cost estimate total $2250.00. This seems very expensive compared to what I am reading on the internet about this repair. Does it seem out of line to those of you who know these things?

The price quoted to replace a Throttle Pedal Control Assembly does seem unusually high. In general, the cost for this kind of repair can widely vary, but it typically falls in the few hundreds of dollars, including both parts and labor.

There are a few things that could be inflating the cost in your case. Dealerships often charge more for parts and labor than independent shops. The quoted price may also include additional services or repairs.

However, before proceeding with the repair, I would recommend getting a second opinion from an independent mechanic. Make sure to ask for an itemized quote to understand what exactly you're being charged for. This will help you determine whether the quoted price is fair and necessary.

Leave a Comment Cancel reply

Save my name, email, and website in this browser for the next time I comment.

Tips and Advice

Tractor Dashboard Symbols And Meanings

Suzuki sx4 years to avoid - 5 worst years, cummins isx years to avoid and why, car with key symbol on dashboard, electronic throttle control warning light on - why, how many lamborghinis are there in the world - 2023 data.

• Remember me Not recommended on shared computers

Forgot your password?

• Engine & Transmission

ABS, traction and service AWD light on

By sidney john April 18, 2016 in Engine & Transmission

• Reply to this topic
• Start new topic

Recommended Posts

Sidney john.

Hi everyone.. need help here please..i have a dodge journey 2012 with 71k milleage unfortunately my wheel bearing driver side give up and i change it by myself, after installing the new bearing and have it for drive check suddenly the 3 lights warning went on (ABS, TRACTION CONTROL,SERVICE AWD) i dont know what i did wrong..please anybody has a similar issue like mine that can help me determine the problem..thanks in advance

Link to comment

Share on other sites.

If you did not plug in the sensor properly, the car will have no idea at what rate each wheel is turning. Hence, no AWD, ABS, TC and I'll bet that your Cruise will not work either.

• 2late4u and John/Horace

yes i did, was install properly thats why i can't figure out whats the cause of lights on on my dash

Unplug the sensor, and make sure you did not bend a pin. They are touchy. Then disconnect the negative terminal of your battery for about 30 minutes to reset your system. See what happens.

• sidney john , OhareFred and 2late4u
• 1 year later...

Shawn Patrick Smith

On ‎4‎/‎18‎/‎2016 at 12:49 PM, sidney john said: yes i did, was install properly thats why i can't figure out whats the cause of lights on on my dash

I have these lights on my dash. I am not sure whats going on but the car has been running fine since I got the car in 2016 brand new. the light s came on yesterday when I went to go out, thinking it was because of the snow and ice build up in the wheel well I cleared that out and tried shutting down and restarting the car, lights went out. went to go out last night and they came on, so I stopped shut it off and started lights went out then came on after I drove a little bit. went home instead of testing the limits. came out to snow blow the drive way, started car only 2 lights ABS and TC came on. moved the car to the street and light s went out. went to go fill the car up with gas and because the street hasn't been plowed yet, theres still quite a bit of snow on the street so when the traction control kicked in car lost some power and then the 3 lights came on again, awd no abs and when the tc light comes on it loses power unless I turn the TC off and only the front wheels spin. because of the holidays the dealer ship is closed. does anyone know if this would be safe to drive until I get it into service?

I would take a picture of your dash showing the light s so when you take it the dealer you can show them what it is doing

Yes it is safe to drive. 

• 2 years later...

Ziyad thaher

I have the same problem. Did you fix it? How?

• 2 months later...

Did anyone fix this for knows how?

John/Horace

Scan for codes to figure out which abs wheel sensor is bad. Then replace sensor and reset with scanner.

• jkeaton , 2late4u and Summer Solstice

What he said   ^^^^

On 4/17/2016 at 9:01 PM, sidney john said: Hi everyone.. need help here please..i have a dodge journey 2012 with 71k milleage unfortunately my wheel bearing driver side give up and i change it by myself, after installing the new bearing and have it for drive check suddenly the 3 lights warning went on (ABS, TRACTION CONTROL,SERVICE AWD) i dont know what i did wrong..please anybody has a similar issue like mine that can help me determine the problem..thanks in advance

I know you probably have fixed your problem but this just happened to me for no reason.  All systems seemed go so before I connected my OBD reader I tried the trick used for resetting the oil change reminder.  Turned the car to run, but do not start it, pressed the accelerator pedal three times holding it down for one second each time.  Turned the car off and then restarted it and the trouble codes went away and the cruise control started working.  It did not happen again.  I am assuming there was something on the sensor and it threw the code when we first started the car.  Until reset it stayed on.  Once reset it did not return.  Just a shot in the dark for you.  I got lucky.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account. Note: Your post will require moderator approval before it will be visible.

×   Pasted as rich text.    Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.    Display as a link instead

×   Your previous content has been restored.    Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

• Insert image from URL
• Submit Reply
• Existing user? Sign In

More Forum Apps

• Online Users
• Leaderboard

|| Forum Activity ||

• All Activity
• Create New...